£0.34 exc vat
£0.41 inc vat
In stock
For use on Diff housing
Remote type case
53K266 are 4.5" long -4 for remote now use TAM1617
53K1471 are 3"long 5/16"unc x3 or use 51K885
Rod change gearbox use-
2-BH506181
2-51K282
3-DAM7760
some pre A Plus used
22G1834 are 4.5" long 3/8"unc with 0.375" thread rod change only x2-use 51K282
CHS2624 are 3."long 3/8"with 0.250"thread x 3 or use BH506181 bolt
53K1471 are 3"long 5/16"unc x3 or use 51K885
£0.34 exc vat
£0.41 inc vat
In stockRecommended usage 1 x BH506181 to fit one mini.
High quality version of 13H9513, INA branded.
Dual use bearing fits the end of the A Plus 18mm mainshaft where the 1st Motion shaft slides on, plus it is used on the A Plus layshaft smaller end.
Kno...
Kit which enables you to fit a rod change gearbox to an earlier round tunnel.
Left hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used. For R/H locktab see 22A962
Right hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used.
Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.
Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...
Mini Spares genuine part, made for reliability, because the current Rover 22G2033version is not good enough. These specials are CNC grooved for correct shape and machined for concentricity using the original type fixings to get the corr...
Extra strong magnetic sump plug. This high quality plug is constructed from 303 stainless steel and houses the latest Neodymium magnet which is currently the strongest available to give the best protection for your engine, even more important when yo...
Complete bolt kit to bolt the transfer case and clutch cover onto the engine block.
Quick release rod change gear coupling a direct replacement for the standard item, doing away with the troublesome roll pins. It comes complete with high quality quick release clips
Originally developed by Rover to cut down on warranty hourly costs on powertrain warranty repairs, by their main dealers.-Labour time allowed at Rover dealers for fitting this seal was 3.4 hours labour rate.
This is a special rigid seal and ...
FITTED from 1984 on-single locktab for the 3 bolt main bearing(double roller)
housing and deleted 1996 on.locking glue used such as locktite
Full rebuild kit with dihferential parts and standard layshaft.
Using only the original manufacturers of the bearings such as RHP because all the Budget bearings are not good enough for longevity or performance use.
This is a full...
Genuine Rover fibre type are now 48 thou thick which is so tight it will probably lock your diff up, they used to originally be .035 thou. These are 43 thou oversize type for worn units but the correct size of 35 thou is available as BTA101<...
The plastic bush at the base of the gear lever stalk ON REMOTE TYPE GEARBOXES ONLY--stops that rattling noise
fit to the gearlever, not the knuckle joint, if it falls of the gear lever there will be a lot of play
Minispares were the first company to produce these layshafts for performance engine/gearboxes as the standard type would flex and resullt in the breakage of the bearings causing seizure. Produced in an upgraded material and heat treated to the correc...
Genuine Mini Spares product, fits 3 and 4-synchro gearboxes except for rod change types which use GAE191. This switch replaces the plug on the front of the remote-shift transmission case. It is triggered internally by the shift linkage w...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.