ROOF AERIAL MOUNTING BASE TWIN POINT MODELS
XUF000020

($33.43) £33.43 exc vat

($40.12) £40.12 inc vat

In stockIn stock
Original equipment on the twin point cars this is the roof mounting base and the ariel comes seperate-See XUJ100070

($33.43) £33.43 exc vat

($40.12) £40.12 inc vat

In stockIn stock

Recommended usage 1 x XUF000020 to fit one mini.

Recommended products

This is the detachable mast part of the roof arial on the twin point cars.

The base unit is XUF000020.



this is the factory standard long aerial, not a short one



measures @ 78cm

Alternative products

Minis always looked better and safer from vandalism with a roof ariel.

An ariel that mounts under the wing for minis. Beware when fitting 13" wheels as Rover moved the ariel to the roof.

People also bought products

An ariel that mounts under the wing for minis. Beware when fitting 13" wheels as Rover moved the ariel to the roof.

Minis always looked better and safer from vandalism with a roof ariel.

This is the detachable mast part of the roof arial on the twin point cars.

The base unit is XUF000020.



this is the factory standard long aerial, not a short one



measures @ 78cm

Wiper motor fitting kit to fit all mk2 onwards wiper motors to the bulkhead.

Interior lamp with a black on/off switch and pointed torpedo ends.

Also fitted many of the 1959on range of Austin A55/60 Cambridge, MG Magnette etc.

Also there was an alternative lamp with black switch and square ends 13H192 which w...

Genuine Bosch lambda sensor, fitted to both the twin and single point injection cars and fitted in the same exhaust manifold shared by both cars. Be warned the cheaper non branded sensors cause lots of issues hence we only sell the Bosch version.

Sports coil for ballast resistor type ignition.

Best internal parts tested and another intermotor top product.

Its not the name on the outside but whats on the inside which matters.

Original type coil bracket 12G29...

Pop rivet for fixing the headlamp bowl to the wing. Great for MS14 metal bowl but be careful if using on plastic bowls

rear stop and tail lamp for early BMc cars with red plastic lens.

Also stocked is a white lens and single filament bulb equivalent for use as reverse light on kits cars and Mokes as CHM13REVERSE.

Lots of things have been written about performance plug ignition wires but regardless of what you believe we all know that good wires are a must. This special competiton wires set from the Lucas factory has 8mm wire and the highest performance, no br...

Small battery cable retaining bracket bolted at the front of the engine for pre engaged manual cars approx 1985 onwards.

Wiper Swithch MK1/2/EARLY MK3 blade type switch for using to convert to 2 speed wipers when current 2 speed wiper motor is used.

For those very early 25D type distributors.Mini Spares version for modern fuels as fitted to our distributor range with slide on vaccum hose inlet pipe-not the very first screw in type

Bolts on the side of the injection body housing to control engine idle speed and air flow from cold start up. The blue socket loom cap fits this unit. This is part of MLZ100090. After fitting the cars ignition needs to be turned on and o...

Set of 4 ignition leads from the original supplier to Unipart, suitable for all twin point minis 1997 onwards. For use with M4 type coil.

Gasket/seal for all 1997 on mpi headlamp bowls (self levelling type).

original Lucas type RESIN BASED CONDENSER made for the 45/59D type distributor if you want a quality item rather than the cheaper inferior parts available. Filled with 3m of winding inside as per original Lucas but every copy analysed to date has ...

NEGATIVE EARTH ONLY..45D electronic(contactless)Pre A plus distributor .

replaces 41824A and 41418 plus any 998/1098cc up to the changeover of A plus type distributors. For best performance and tune we advise our electronic evolution versio...

Resistor for AFU3389LED and AFU3389WLED, this is needed to enable the lamps to function properly. Sold in pairs.

Coil bracket fitted to end stud of cylinder head,clutch end for coil to mount on as fitted 1969-94-MK3 on. This has been made to the original specification with the welded lug nuts rather than the cheaper method of having just plain holes to take a b...