VALVE EXHAUST 88G459 SMALL TYPE COLLET
12A1987

£4.90 exc vat

£5.88 inc vat

In stockIn stock
Pre A Plus exhaust valve using 88G459 small cotters. Uses AEA311 springs-25.4mm. For 850/998/1100cc. This valve is to a higher spec than the originals.

£4.90 exc vat

£5.88 inc vat

In stockIn stock

Recommended usage 4 x 12A1987 to fit one mini.
Cylinder Head 850CC, 998CC & 1100CC Pre 'A' Plus - Qty 4
997CC & 998CC Cooper Cylinder Head - Qty 4
Cylinder Head, 998CC, 'A' Plus 1980 on - Qty 4

Recommended products

Valve spring sold as singles for Pre A plus 850/998/1100.

This was also the outer on the 997/8 cooper range but the inner is obsolete so use our C-AEA525 where the outer was the same length.

12G1015 was used on many A ...

These are the exhaust valve seats for lead free small bore cylinder heads

850/998/1100. If you require inlets see TAM2152.

Fitted from 1988 with introduction of press fit high compression pistons although many earlier h...

As an engine wears, the clearance between the valve stem and guide increases; as this gets beyond tolerances the car will tend to smoke under deceleration (when you take your foot off the throttle). Good valve stem seals will allow for greater wear b...

Genuine Mini Spares product as everything else on the market was poor fitting and unstable.

For Performance see 88G459EVO made in the USA by a Specialised Racing product company.

All the earlier heads used the 2A11 cott...

People also bought products

New competition valve cotter for early heads with the large single groove valve, these are precision CNC machined from 4340 and heat treated to a better spec than EN24T and claimed to be stronger in fatigue life.

These locate better in the v...

Spring seat shims (set of 4), 0.020" thick (0.5mm).

Spacer shims to increase valve seat pressure and overall spring rate.

These were also used on all the 8 port head valve seats to prtect the alloy seats from wear. (8 port now C-AHT...

Spring seat shims (set of 4), 0.040" thick (1mm).

Spacer shims to increase valve seat pressure and overall spring rate.

These were also used on all the 8 port head valve seats to prtect the alloy seats from wear. (8 port now C-AHT36...

Fitting kit comprising of studs, nuts, plain washers, spring washers and a gasket

New competition valve cotter, these are precision CNC machined from 4340 and heat treated to a better spec than EN24T and claimed to be stronger in fatigue life.

These locate better in the valves and easier to control spring heights.

Set of strong lightweight titanium top caps to suit our valve springs C-AEA526/527 hard for single collet competition valves. Sold as a set of 8.

Genuine Mini Spares valve stem oil seal manufactured with original Dupont Viton, as fitted to the twin points engines, are the best material and seal you can use and although expensive are the best to date in stopping the engine smoking.

Man...

1.2"(31mm) intake valve for 12G295 Cooper head 998cc. Also a suitable upgrade for other small bore heads. These have the large collet groove 8.65mm (.340") 2A11 cotters which are now available as 2A11EVO. Correct grade exhau...

Originally fitted to Minifin rocker covers as standard Rover equipment, it will also fit almost every other rocker cover including our FP26 range and Minispares alloy covers. This improved cap has a large grip and an improved lock system...

Best quality 1" exhaust valve for small bore cylinder heads as fitted standard to 998 Cooper. Higher grade than AEA434. Has a large 8.65mm (.340") collet groove 2A11 cotters which are now available as 2A11EVO.

1.1" diameter intake valve for 948cc with 8.65mm wide groove for use with the original 88G616 top caps and 2A11 cotters which are now available as 2A11EVO.

Sold individually.

To help rocker pad to valve stem alignment and reduce friction, the standard springs can be replaced with solid spacers and correctb shim set. The spacers and shim kit are sold as C-AEG392.

160lbs on the nose at 400" for standard Cooper S or twin spring set ups. See C-AEA526 and C-AEA527 for later developed springs. These are ok for all standard uses but are improved and uprated over all original factory fitted...

Genuine version of the thermostat gasket for all A series. Black one side and red the other they are fitted black side to the head. Green to the thermostat.

We have no evidence as yet that they last longer but do look good.

See [lin...

Spacers for under the rocker pedestals are used mainly by engine tuners to allow tappet adjustment to be made where cylinder head mods have been carried out. 1.3mm/0.0512" thick, this can be used to hold locating screw on rocker post assembly but the...

Goes with 12A1987 ex valve and should use AEA311 valve springs. 27mm. Pre A Plus for 850/998 with 88G459 small cotter grooves. Supplied singly, 4 required per engine.

Early Large cotter groove exhaust valve. Most small bore engines seem particularly prone to burning valves, it is highly recommended to replace the exhaust valves when you do a valve job! This 1.0" valve fits most early 948cc, 998cc and 1098cc engine...

1.402" (35.6mm) dia x 3.57" long intake valve.

Our race valves are produced in EN214N steel and are stellite tipped and use the latest triple collet groove and current valve head shapes, plasma heat treated for eradicating unleaded petrol we...

Originally marketed by minispares in the mid 70s so many companies copied them because of their smart looks and ease of fitment they were improved by offsetting the arms to help tighten plus stop the arm falling out when they were straight. These T b...