£23.50 exc vat
£28.20 inc vat
In stock
Make sure you fit the plastic blade the right way, the smoother moulded centre faces the engine, which might look wrong to some people, our picture shows the side that faces the radiator. If there is an F or word "front" stamped on it then that is the side that faces the radiator.
Minis from 1959-69 and 1990-1 had 12G1305 a thinner blade 1.100 wide at tips whereas this is 1.5"
£23.50 exc vat
£28.20 inc vat
In stockRecommended usage 1 x 12G2129 to fit one mini.
Known as the 'Hot Climate' or 'Export fan' this metal fan is moves the most air but also absorbs the most power.
The 11 blade plastic fan 12G2129 is quieter and is the most efficient in terms of power absorption and air movemen...
Replacement electric fan assembly complete with laser cut metal brackets so that it can be mounted to the original mounting points of the standard fan
uses 9" blowing air fan.
A must for any tuned road car. A full electric fan kit, Mini Spares helped to design with precision made brackets to mount directly to the mini radiator to suck air in order to maximise efficiency and cooling. It therefore does not block cold airflow...
This electic radiator fan was fitted as standard on minis with the large round hole cut out in the inner wing fron 1991. On the 1275 Cooper last carb models there was an earler type fan which is also no longer available. As the original Cooper carb f...
Plastic electric 10 blade universal 10" sucking type fan unit only-12 volt-for cooling your water temperature. This is also the donor part in our PGG10058MS kit.
Used with most of the standard fans, definitely required if you have a breather type timing cover.
This spacer is: 4.05mm thick/0.162"
Single blade. This is our copy of the original special tuning fan blade that we have been selling for nearly 20 years. Many people use 2 of these blades crossed over to make it a four blade fan which does makes it slightly quieter. Sold as single bla...
FITS INTO SANDWICH PLATE ON CARB COOPER HAS M8 THREAD 8MM WIDE
Known as the 'Hot Climate' or 'Export fan' this metal fan is moves the most air but also absorbs the most power.
The 11 blade plastic fan 12G2129 is quieter and is the most efficient in terms of power absorption and air movemen...
Fitted from 1990 on until twin point cars but also found on some earlier cars with 12G2129 fan blade.
This spacer is: 12mm thick
This radiator electric fan was fitted as standard on minis with the large round hole cut out in the inner wing fron 1991 on the last carb models through to the SPI but there was an earler type which is no longer available that was on earlier 1275 coo...
Long lasting silicon by pass hose between cylinder head and water pump.
These are easy to cut and slide on easier than the old conventional rubber type.
It has been made this length to fit 1275cc engines which used the longest hose....
Replacement plug and washer for Minispares 2 core and 4 core radiators
Silicone hose kit for 998 vehicles from 1989 onwards that were equipped with the plastic inline heater valve, comes complete with moulded heater take off pipe and 5/8 heater pipe.
Silicone hose kit for 998 vehicles from 1989 onwards that were equipped with the plastic inline heater valve, comes complete with moulded heater take off pipe and 5/8 heater pipe.
Silicone hose kit for 998 vehicles from 1989 onwards that were equipped with the plastic inline heater valve, comes complete with moulded heater take off pipe and 5/8 heater pipe.
Heater hose that comes from the cylinder head take off to the plastic inline heater valve on 998s 1988 on - this can also be used with a heater take off on 1275cc engines.
Original 7/16" spring type hose clip as used on later cars (approx 1990 on) for some radiator hoses and fuel lines.
MPI only. 3 YEAR GUARANTEE-UK made.Large impeller higher capacity water pump. Mini Spares procured product as original Rover Airtex tooling has been scrapped.
Fitted with a PPS, glass filled plastic impeller as used by Jaguar and Aston Marti...
3 YEAR GUARANTEE-UK made.Large impeller higher capacity water pump with top quality die cast body . Mini Spares procured product as the original superb Rover Airtex tooling has been scrapped.
Fitted with a PPS, glass filled plastic impeller...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.