£9.60 exc vat
£11.52 inc vat
Out of stock
£9.60 exc vat
£11.52 inc vat
Out of stock
Single replacement unit for the right hand drive kit S4698B with left hand dip
lamp part only, does not include the rubber cover, bulb or side light part
These are R/H/Drive, see S4699B for L/H/D.
Even at normal highway speeds it is common to "outdrive" conventional headlamps. These halogen headlamps have very bright 55/60 watt bulbs. Their special lens gives good long range visi...
This is supplied in parts as a bowl with inner rim,sealed beam amd outer rim, easy to install and a lot easier to cope with than trying to repair that rusted or bent old unit. High quality sealed beam lamps with a plastic bowl and Minispares stainle...
The best chrome type available with screw and washer.
A headlight trim ring is only the starting point of a good looking car, but you have to start somewhere. Sold singly 2 required per car. These are the original type chrome over solid bras...
These are for Left had drive L/H/D. See S4698B for Right hand drive R/H/D.
Even at normal highway speeds it is common to "outdrive" conventional headlamps. These halogen headlamps have very bright 55/60 watt bulbs. Their special...
These are R/H/Drive, see S4699B for L/H/D.
Even at normal highway speeds it is common to "outdrive" conventional headlamps. These halogen headlamps have very bright 55/60 watt bulbs. Their special lens gives good long range visi...
If your rusted old headlight bucket is getting to you, don't waste time trying to salvage it when new metal reproduction metal buckets are AVAILABLE.
With a headlamp rim fixing bracket 37H7421 attached
Whether you are ...
The headlamp bucket is isolated from the body with these rubber seals/gaskets.
Headlamp sundries kit.
Includes two adjuster screws, plastic nutserts, pullback spring. Two kits are required per car.
A plastic lamp spade connection with sidelight bulb aperture for use on sealed beam units only. Uses a GLB501 capless bulb. The mini clubman used sealed beams but had independant side lamps and therefore had an equivalent unit less the s...
This plastic bowl kit includes the inner rim to hold your light unit and will obviously not rust like the old originals. You will need a headlamp outer rim so why not fit our own developed stainless steel variety which is cheaper than even chrome bud...
These stainless steel peaks fit under the headlamp rim to give that old 60s style again.
Screw for holding PRC1230A to the number plate light body, 1970 onwards.
Stainless steel screw kit for all mk2/3 lens to lamp body. Comes as a car set with six screws and six fibre washers.
The half bowl for holding original sealed beams into the headlamp bowl om minis and many other headlamps of the 60s and 70s. Sold singly 2 required per car.
Foam gasket that goes between the indicator/side lamp unit and front panel for all clubman models
Genuine Mini Spares L/H lamp with white lenses. This type of lamp was fitted from 1976 on as standard equipment with a built in reverse lamp.
Supplied with gaskets and correct coloured bulbs this has the more fashionable/retro white upper ...
THE LENS FIXING SCREWS FOR THE REAR LENS ON MK4 1976 ON WITH REVERSE LENS ARE ALL THE SAME. SOLD INDIVIDUALLY. ALSO FITS TWIN POINT FRONT INDICATOR LAMP.
3 per lamp required or 6 per car set.
Interior lamp bayonet type bulb from late 1984-10 watt the same size fitting as GLB207 which is often used although only 5 watts.
Sold individually, these are R/H/D.
RHD HEADLAMPS DIP TO THE LEFT.
Brand new Free Form light unit from Wipac with clear Polycarbonate lens but the backing bowl is specially designed to reflect the beam and give better pen...
This chrome over brass wing side repsater lamp rim will fit of the square/oblong lamp lens where fitted on the wing. Fits straight over the original lens and retained by bending the tag. Made in brass to prevent rusting, but also to obtain that deep...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.