£232.50 exc vat
£279.00 inc vat
In stock
£232.50 exc vat
£279.00 inc vat
In stockRecommended usage 1 x 14A6895 to fit one mini.
Rear subframe mounting stiffener L/H repair bracket with holes for subframe mounting and attaches to wheel arch Fits on ALA8623
Good quality pressing rear upper side panel,used for converting clubman estates to van sides or repairing van upper section back to original when windows have been fitted. This is L/H side.
A post inner closing panel/siffener plate R/H external hinge cars.
Not always stocked owing to lack of demand but available to order.
Reproduction version os ASJ360070. For the twin point only as it changed shape to accommodate the front mounted radiator and different bonnet fittings.
For vehicles with external hinges and sliding type windows this is a full inner front wing with the wheel arch panel. The panel is what that the outer A panels for the hinges attach to.This is the left hand pane wing with radiator vent slats but not ...
For vehicles with external hinges and sliding type windows this is a full inner front wing with the wheel arch panel. The panel is what that the outer A panels for the hinges attach to. This is the right hand panel made by Heritage but not 100% perfe...
Commercial Mini floor extension
It is an essential part for the correct restoration of all the longer wheelbase mini derivatives. From the original tooling.
NON genuine 8"wide outer sill for the van/pick up and estate range with MK3 square pressings. No genuine wide panel is available but see 14A9026/7 for 4" wide panel which actually covers only 2.5" of actual lower floor pan whereas the non genuine pan...
Aftermarket wings do the job at a fraction of the cost of originals. This right front wing for the Mini will fit all MKI, II, III, IV. A slight difference exists between the early and the later models as to headlamp mounting holes. These reproduction...
You can spend hours cutting out rust and patching holes, but why bother? These reproduction floor pans extend the full width with vertical flanges for easy installation and fairly well represent the original stamping. They have added metal to include...
Floor,Front and rear assembly for Rod change gear lever cars 1973 on less the crossmemeber. This floor is the latest shape ever made wich is stronger and has a gusset section down the L/H side to carry extra fuel lines. Also see HMP441004/5 floor sec...
The crossmember holds the seat brackets and has the correct shape on the bottom to sit correctly on the floor of the rod change tunnel only. This is the complete section from inner sill one side to the other. Fits all square type rod change gearbox f...
NON genuine 8"wide right hand outer sill for the van/pick up and estate range with MK3 square pressings. No genuine wide panel is available but see 14A9026/7 for 4" wide panel which actually covers only 2.5" of actual lower floor pan whereas the non ...
This early front (nose) panel will fit any Mini manufactured before 1976. It is probably easier to replace the entire panel than to repair a damaged one, especially if it's been hit more than once! Later Minis with rubber mounted subframes, use panel...
You can spend hours cutting out rust and patching holes, but why bother? These reproduction floor pans extend the full width with vertical flanges for easy installation, and fairly well represent the original stamping. They have added metal to includ...
Non Genuine for the Pick-up and Van with a slat type fixed grille as a trademark for Mini commercial type vehicles originality.
This good reproduction is the only panel available to allow you to restore it easily.It is a modified saloon pan...
THIS PANEL PROTECTS THE UNDERSIDE OF THE WINDSCREEN VALANCE UNDER THE FRONT WING SECTION also fitted on the inner wing panel 14A8346/7
This panel has mounting holes for later models facia crash panel. These holes will require blanking for true originality on earlier models without the facia pad
floor pan front to rear for the left hand side only to the correct floor shape before 1990-1 rib design change---ideal for MK1/2 restoration with original 4 flute indentation. This has the carpet stud brackets plus underside slinger bracket and mul...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.