£88.00 exc vat
£105.60 inc vat
In stock
£88.00 exc vat
£105.60 inc vat
In stockRecommended usage 1 x 27H4775 to fit one mini.
Special Tuning hit upon this idea to stop the driveshafts breaking on their rally cars. Do away with the large circlip groove where it broke and weld a spacer on the shaft to locate the CV joint in position. The works department also reduced the stee...
Special Tuning hit upon this idea to stop the driveshafts breaking on their rally cars. Do away with the large circlip groove where it broke and weld a spacer on the shaft to locate the CV joint in position. The works department also reduced the stee...
Non genuine aftermarket only as the genuine originals are obsolete.
These are the best on the market where clip grooves are in the correct place to save the driveshaft seizing on. Later model Minis have CVs on both ends of the axle; this is ...
There are 4 of these to each output flange to which the Hardy Spicer joint bolts. The special philidas nuts for these are our number GFK3431.
Sold Individually.
In board CV joint(pot joint) gaiter kit with plastic clips and grease.
Non Genuine item many sell as GSV1073.
The single largest reason for the failure of this rugged assembly is contamination, dirt and moisture will destroy one ver...
Hardy-Spicer coupling was fitted to the Cooper "S" and all automatic varieties pre Pot joint(inboard cv joint) This U-joint assembly slides onto the driveshaft and bolts to the Cooper S output shaft flange. The U joint fitted to these joints is the s...
Rubber U-joint for yoke-type driveshafts. These are the only new supply available except for QL5000 alternative.
The very early Minis used the rubber U-joint drive couplings to eliminate harshness being transmitted to the passen...
Special grease for Cv joints and any homokinetic joints. Enough for one joint only.
Steel driveshafts with original circlip holes, ensure that the cv circlip clicks fully in both shaft and cv joint.
These are upgraded to stop the ends twisting off. Available for rod change also as C-BTA1264 SOLD AS A PAIR
One gaiter, 2 plastic clips and grease. The single largest reason for the failure of this rugged assembly is contamination. Dirt and moisture will destroy one very quickly. The CV rubber boot protects the joint at all angles but if your boot shows an...
This is the small gaiter that sits on the yoke and shaft of all pre pot joint rod change minis. Also fitted on autos and cooper S hardy spicers.
Genuine Rover Xparts item. See BHM7012 which many vendors sell as their GSV1073.
In board CV joint(pot joint)gaiter kit metal clips and grease.
The single largest reason for the failure of this rugged assembly is contam...
Thin driveshaft circlip for outer c.v joints.
Also replaced 22G2688 for the inner pot joint circlip. Not required for hardy spicers or rubber cross type inners couplings. Sold singly 2 required per car.
Metal CV gaitor ties for the outer CV gaitor, slim in design in order to give maximum clearance between CV and hub
Evolution RACE quality universal joint for hardy spicers If you want to prevent disaster, you should check your driveshaft joints before they self destruct! The best and easy way to do that is to listen and feel the car as you lift off the throttle w...
Molybdenum Grease supplied in a 500g tub, suitable for the lubrication of CV joints and any other homokinetic joints.
Genuine Mini Spares Heavy duty gaiter kit as supplied with our GCV1013 cv joint, contains rubber gaiter grease and metal clips. We consider this the best available with a special shape to stop rubbing or soiling.
Sold singly-2 r...
As fitted to MPI from 1996 on with an extra O ring. The O ring goes between the first bearing and backplate on stub axle. Rear tapered roller wheel bearing kit, for one wheel.
All post 1985 cars and the Mini Cooper S were equipped with very...
Special height locking type nut for the hardy spicer joints on Cooper S and automatics to fit the 22A1139 bolt. Sorry about the price but only available from Philidas Ltd.
Heavy duty needle roller type coupling with plastic ends. The very early Minis used the rubber joint drive couplings GCD101 to eliminate harshness from being transmitted to the passenger compartment. Over the years the rubber will separa...
Cheaper alternative to genuine timken front bearing kits.
These are very well tried and the best of any of non genuine bearings available.
Sold as one hub kit only. Please note-for arduous or race use Timken bearings in genuine GHK1...
Inboard CV (pot joint) splitting tool used to remove the constant velocity joint from the gearbox by way of driving this wedge-like tool between joint and gearbox. Does not remove joint from driveshaft.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.