£222.90 exc vat
£267.48 inc vat
In stock
The same loom in PVC is 5L322.
Same loom but for cars with temp gauge in 3 clock pod from A2S7 197021 order WL302 for PVC covered or WL322 braided loom.
Van and Pick Up equivalents are also available to order. Complete with rear loom.
£222.90 exc vat
£267.48 inc vat
In stockRecommended usage 1 x 5L191 to fit one mini.
Dip switch lead for right hand drives cars, these are not included with new looms.
Dip switch lead for left hand drive cars, these are not included with new looms.
PVC wiring loom for MK1, floor starter with coil on dynamo and single speedo clock only. 1959-62 without temp gauge-to A2S7-197020- before temp gauge fitted.
Same loom in braided is 5L191.
Same loom but for cars with temp gauge in 3...
Inertia starter -no side repeaters on wing -Instrument cluster in front of driver,either 3 clock with tacho or 2 clock cars but ignore wires from distributor for tacho and tacho wires.
On pre 1984 cars the wiring for the indicator...
All Minis require an earth strap from the engine to the body and from 1959-1996
they fitted from the gearbox to the subframe. When they introduced the twin point in 1996 it was moved to the upper engine stabiliser arm. About 13"LONG.
Universal post type battery earth strap with clamp type fitting and correct length for most alternatives of batteries fitted.
The battery cover made of a special cardboard as fitted to all minis to protect
the battery terminals from metal objects. See also the 14A7666 retaining strap.
A plastic lamp spade connection with sidelight bulb aperture for use on sealed beam units only. Uses a GLB501 capless bulb. The mini clubman used sealed beams but had independant side lamps and therefore had an equivalent unit less the s...
The only battery cable to run the full length of the Mini, this has a positive type terminal that clamps arond the post rather than the helmet or cap type on much earlier cars. Some cars had slightly shorter cables than this but measure your old cabl...
Complete braided wiring loom for Cooper S MK1 with dynamo and oil filter light switch--as very few of these warning lights still work this loom is also supplied for cars without oil filter waring light and ignore extra wires.
For alternator...
Large grommet to fit 1"approx holes in bulkhead for items that need to be able to flex and move such as capillary tubes and oil pipes. 7/32" hole size.
The small hole will expand and is also used as wiring loom through bulkhead and battery c...
This plug fits the hole in the inner wing where the wiring for the wing side repeater lamp goes through the body on cars after 1986.
RESIN BASED CONDENSER as per the original Lucas type made for the 23/25D type distributor as fitted to original Cooper S or Racers who want a trusty part or where originality is required,with soldered wire connections and correctly made foot to sit ...
Stainless steel screw kit for all mk2/3 lens to lamp body. Comes as a car set with six screws and six fibre washers.
Single bullet connector used to join the front loom to the rear loom near the wiper motor.
Double bullet connector used to join the front loom to the rear loom enar the wiper motor.
These are the screws needed to fix the condenser, points and base plate to 23/25D distributors. See 57H5135 for 45D type distributors.
With an integral push start button built in the solenoid as originally fitted to early minis. The activation of the starter motor starts with the key (or push button in the early cars), but the most important function is carried out by the solenoid....
Replacement Distributor ignition module fitted to all standard electronic ignition distributors (non injection) looking at the front of module, negative is on the left. positive on right and centre pin is not used.
This chrome over brass indicator lamp rim will fit any dome shape lamp lens that is retained by 2 screws, including Twin Point cars. Fits straight over the original lens and retained by the original screws. Made in brass so that a deep chrome finish ...
the oil seal to fit on 12A1136 distributor housing. Pre A Plus
the earlier housing 2A612 did not have a seal.
If you have an original 25D type distributor this is an upgraded arm (blade moulded and riveted )for performance use because all the other types available now are likely to fail at high revs. Because the blade is thin,or the rivet sometimes to long a...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.