ROSEJOINT SPACER FOR C-AJJ3360 LOWER ARMS
AN1372

£2.58 exc vat

£3.10 inc vat

In stockIn stock
This is the spacer for fitting either side of the spherical joint or rose joints on lowers arms, made to fit all our lower arms with this type of fitment. Sold individually

£2.58 exc vat

£3.10 inc vat

In stockIn stock

Recommended usage 4 x AN1372 to fit one mini.

Recommended products

Ultimate lower arm for road or race. (pair supplied)

One piece, forged, fully adjustable on the car lower arms (with knuckle for bushes) to allow adjustment for any camber setting required. Sold in pairs only. It is recommended that you fit ...

Kit products

one piece forged lower rod end arms

unbelievably at this price they are not the welded type as sold by many of our competitors

Same as the C-AJJ3360 lower arm kit, but includes the spherical rod ends,spacers and dustcov...

extra parts required to convert the C-AJJ3360 lower arms to spherical rod end type if the arms were previuosly purchased-These parts are available with the arms as C-AJJ3360A as a money saver

Ultimate geometry kit for competition use which includes following parts. Adjustable tie rods with Mini spares tie bar bush kit (not spherical joints) and Spherical jointed lower arms with the dust covers. For the rear a set of camber and tracking br...

People also bought products

Genuine Mini Spares standard performance cone utilizing 20 years of elastomer/rubber technology from our competition cones manufacturer. Only beeen available since 02/09/2020 and proudly made in the UK with 10,000 sold by 2023.

Original cone...

Genuine Mini Spares UK made complete joint with the following specifications,

correct dimensions and shape of pin and ball in EN24T, using correct spec grease,

genuine original shape cup using correct material (21A423MS...

Standard gas filled replacement front shock absorber from Bilstein.



Non hand adjustable front damper guide ratings

442001 KYB standard replacement

342001 KYB Gas filled 25% upgrade on sta...

Replacement ball joint shims, comprising of 2x 003"(.076MM) shims, 2x 005"(.127MM) and 2 x 010"(.254MM).

Tie rod extra hard rubber bush, harder than standard.

You dont want these bushes too hard as it can cause the threaded on the end of the tie rod to break under extreme conditions.

In theory the outer ones should be harder for rigidi...

Mini Spares quality suspension kit includes all four adjustable alloy trumpets and knuckle joints plus the two extended rod struts required for the rear. Many people will advise you, why you should consider upgrading to the genuine classic "Hi/Lo" su...

Car set of 4 top Subframe tower mountings for Road cars from 1976-2000.

Aluminum pad for the top of each subframe mounting and a poly pad below to replace the standard rubbers originally fitted. The alloy pads help reduce subframe movement, ...

extra parts required to convert the C-AJJ3360 lower arms to spherical rod end type if the arms were previuosly purchased-These parts are available with the arms as C-AJJ3360A as a money saver

one piece forged lower rod end arms

unbelievably at this price they are not the welded type as sold by many of our competitors

Same as the C-AJJ3360 lower arm kit, but includes the spherical rod ends,spacers and dustcov...

Genuine Mini Spares product ideal for road use for maximum performance, where other examples available tail off as they get worked and heat up.

Hilos will be required to enable fitment as they are taller but FAM3968EVO are a str...

Lower suspension arms to give 2.0 extra degrees of negative camber. Stamped with 2.0 Sold in pairs only.


General:See also c-AJJ3360 fully adjustable arms

Negative camber lower arms are specifically forged in different degrees to...

Angled grease nipple for the upper arm on the front suspension of all Minis

importantly lubricates the upper arm spindle which so often gets neglected so check yours out and make sure this nipple is working properly. Also fits rear radius ar...

Lower arm top hat bush in poly to fit all lower arms with twin taper as standard from 1965. Mini Spares have upped the game once again with these superbly finished bushes which surpass anything on the market. Fitted with a metal bush insert these are...

A must-when the castor and camber angles are changed or whenever the geometry of the car is set up you will require these bushes. They are good for cars with up to 3.5 degrees of castor angle.

From November 2003 they have been made from a s...

Genuine Mini Spares part improved from original for the R/H upper mounting point of your damper(shock absorber) and fit 14A6948 captive nut plates for upper bolt fixings . For lowered suspension use C-AJJ3359

These cone springs will require Hilo adjustable suspension as they sit higher than the originals.Containg an anti fade property and shape which helps them going off during racing and giving hopefully a season of racing before replacement. A softer ro...

Uses 2 Soft standard rubbers on the insides and the 2 Mauve poly on the outside.

HARD OUTERS / SOFT INNERS - STOPS BRAKE WEAVING.

Don't be confused as this special shore hardness set up was proven after 2 years of testing and is per...

Each Hi-Lo Suspension Kit Includes one pair of Hi-Lo trumpets and nylon knuckle cups which will fit front or rear, but you will need the sleeved rods HILO-01 to enable fitment to the rears. For a car set you require 2 HILO k...

Mini Spares own to original drawing specifications with heat treatment correctly applied where appropiate.Lack of proper maintenance (grease) will make the pivot shaft and/or bearings wear that much faster. In severe cases the shaft may rust to the b...

Minispares dry suspension type bump stop with 2 threaded retaining bolts which was replaced by a single bolt on MK4 cars from 1976 on. For 1976 on see FAM2764 or FAM2764MS. (nuts not included)