£4.80 exc vat
£5.76 inc vat
In stock
£4.80 exc vat
£5.76 inc vat
In stockRecommended usage 1 x C-AHT94 to fit one mini.
"Y" Piece for Maniflow LCB C-AHT365 in stainless steel. With boss
for sniffer pipe as used by Rover for emmisions testing.
Standard bore LCB (1-3/4" id) for standard to high performance 1275s and for street 1380s. This is the same manifold as the standard C-AEG365 but with a slightly different shape to allow fitment to cars fitted with rubber coupling drives...
This is the clamp on the cooper freeflow manifold to clamp it to the engine for extra support, supplied with tag.
Standard bore Budget priced LCB (1-3/4"id) with pre cast flanges to improve flow and save engine tuners time matching the ports. This is ideal for very hot small bore engines and for standard to high performance 1275s, including road 1380s.
Small bore Maniflow LCB. Has a 1.5" outer diameter 1.375" internal diameter bore size. STD mini exhaust and downpipe size is 1.250".
If the 1.375" tapered end of about 2" is removed a 1.750 pipe will fit over remaining length of outlet pipe.
Special reinforced gasket for injection cars has metal inserts on exhaust ports plus a metal back on the manifold side which makes surface easier to clean when replacing. Often used on Turbo cars when correct gasket is in short supply.
...
Exhaust manifold to downpipe clamp.
The key to eliminating exhaust leaks at the manifold flange is the clamp. These new clamps include proper brass nuts and support washers. Fits most 850cc, 948cc, 998 etc. Those engines with single carb an...
Standard bore LCB (1-3/4"id) that is ideal for very hot small bore engines, for standard to high performance 1275s and for street 1380s.
There is NOT enough clearance room when fitting to old cars with rubber couplings which foul. Using [lin...
Maniflow's tubular reproduction of the original Cooper 997/998cc exhaust manifold manufactured out of the same tubing as the STD bore LCB. This free flow manifold works vey well at lower speed pick up, the LCB is noisier but better at the top end of ...
Special tin plate type of gasket that goes between the manifold and exhaust downpipes on all injection cars.
The intake/exhaust manifold should be secured to the head with brass nuts and these very thick washers. These washers are intended to not only spread the clamping action but the thickness allows them to absorb the heat without deforming! Takes 4 per ...
This short pipe fits on the end of our freeflow manifols C-STR816 to give the overall length of an LCB when you have an exhaust system to fit that was made explicitly for LCB fitment.Total length is 300mm ID is 44mm OD is 48mm.
This popular size clamp fits the y piece where it joins the manifold on all our standard long centre branch exhaust manifolds. Sold singly.
The correct length and size downpipe when fitting a turbo power unit into a mini with a knuckle joint for extra longevity. 2" outside diameter pipe
Manifold gasket fitted to all A series pre 1992 except Turbo which had a reinforced exhaust ports GUG704063MG and SPI from 199. From 1991 on a new better gasket with reinforced exhaust ports and backing was fitted GUG704053MG
Maniflow's reproduction of the original Cooper header, but manufactured out of the same tubing as the STD bore LCB.
MADE FROM 409 GRADE STAINLESS.
If you wish to delete the catalyst (legal restrictions apply, so check to see if you are allowed) this pipe is specially made to replace it.
Link pipe for fitting between the LCB and the catalyst. It has a stainless steel knuckle joint to prolong life and give the flexibility required on the system to overcome damage. See also alternative RC40-016
Y piece replacemen...
Special length and thread pattern only for the exhaust manifold to downpipe of injection cars, see also FX108047 special nuts. Metric M8.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.