£115.50 exc vat
£138.60 inc vat
In stock
Remove grille and bumper (then discard overiders if fitted).
Loosely fit centre bracket and lamp bar to middle bumper hole with lamp bar attached. Loosely fit outer brackets to lamp bar and line them up to front panel in the required position before drilling front panel.
The grille then needs cutting away at the bottom to slide down over the 2 outer brackets. On MK2/3 grilles the bottom finisher needs cutting away the width of the outer bar brackets and then upwards, usually to the first slat on 11 wide slat grille or about 25mm. Try not to cut all the way through the grille back panel as it supports the slats. The grille then slides down over the two outer brackets and the grille modifications are rarely noticed.
£115.50 exc vat
£138.60 inc vat
In stockRecommended usage 1 x C-AJJ3329 to fit one mini.
This very heavy duty bonnet strap is a excellent reproduction of the original factory Special Tuning department special. Original light colour Tan leather
3.3mm thick from the tanneries for use on horse bridles, with alloy fastening. Screws ...
Original works quick lift jacking brackets (one pair). Two were fitted both front & rear about 12" apart from the centre, which meant the car could quickly be raised by overcentre quick lift jacks as used by Formula One Teams to this day.sold as a pa...
This is a black painted lighter version with fittings of our s/steel works bar
SEE also C-AJJ3329 for stainless steel.
These cannot be fitted with front overiders and the bottom moulding of the grille slat and back p...
Pair of high power Chrome Fog lights. 5.5"( 135mm )diameter, 50mm deep with durable plastic covers. Universal fitting. The lamp is nearly all forward of the mounting bracket making it great for fitting in front of mini grilles. Bulbs are H3 type 55 w...
Copies of the originals in vinyl
Incorperating the original small clear window to show if the lamp remains switched on.
Copies of the originals in vinyl
Incorperating the original small clear window to show if the lamp remains switched on.
You should always use this kit for fitting any auxiliary spot or fog lamps.
Kit contains wiring and safety relay-cheaper than a burnt out engine compartment.
Please note, SPI and MPI cars have this facility built as standard safety ...
Four LA1009 halogen black bodied driving lamps approximately 170mm wide by 58m deep with 4-XBU10046 stainless steel fitting brackets.
This bracket is required to re-locate standard fitment fog lamps on R/H/D cars when fitting corner bars and overiders to the rear bumper.
Pair of Chrome WIPAC spotlights. 135mm in diameter, 60mm deep with covers. The lamp is nearly all forward of the mounting bracket making it great for fitting in front of mini grilles. Bulbs are H3 type 55 watts GLB453.
Copies of the originals in vinyl
Incorperating the original small clear window to show if the lamp remains switched on.
Reverse Light
Most early Minis did not come stock with a reverse light. This hanging light from Unipart will do the job! It can be conected direct to you gearbox by using
GAE191 switch on rod change gearboxes only.
3" high ...
This is a black painted lighter version with fittings of our s/steel works bar
SEE also C-AJJ3329 for stainless steel.
These cannot be fitted with front overiders and the bottom moulding of the grille slat and back p...
This lamp unit comes without a bracket and will fit either side, if your bracket is okay. The unit only comes from Rover with bracket but costs £29-93 so we supply it less a bracket at £10-00 savings. If you require a bracket for the right hand it is...
Late model cars have these bright red auxiliary "safety lights" mounted below the rear bumper. They are to be switched on during inclement weather. Upgrade for your safety, a legal rquirement on late cars.
These plugs are for the 3/8" holes in the front panel where the spot or foglamp brackets would be fitted, on late front panels.
Original shape washer jet for Mk1/2 minis. Made to the same specification as the last type made for rover parts sales with a nut on a loose thread so it can be tightened easily by hand in the engine bay without any modifications. Should be used with ...
INDICATOR LAMP WITH WHITE LENS AND LED BULBS. sold singly,2 required per car
Stainless steel screw kit for all mk2/3 lens to lamp body. Comes as a car set with six screws and six fibre washers.
This very heavy duty bonnet strap is a excellent reproduction of the original factory Special Tuning department special. A copy of our Tan leather strap, but now available in black.
3.3mm thick from the tanneries for use on horse bridles,wit...
Roof gutter trim clip in stainless steel, ideal finishing item for our MT632 roof gutter trim.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.