£21.50 exc vat
£25.80 inc vat
In stock
£21.50 exc vat
£25.80 inc vat
In stockRecommended usage 2 x C-AJJ4005 to fit one mini.
LARGE ALLOY HEAVY DUTY ALTERNATOR BRACKET FOR ALL PRE A PLUS ENGINES(PRE 1980) AS USED ON ABINGDON ST WORKS CARS
Copy of the original heavy duty works lamp bar with all fittings but now in stainless steel for longevity.This type was used on LBL66D on the 1967 MONTE CARLO RALLY WITH THEIR NOW LEGAL LIGHTS Consists of a central support bracket and 2 end supports ...
This very heavy duty bonnet strap is a excellent reproduction of the original factory Special Tuning department special. Original light colour Tan leather
3.3mm thick from the tanneries for use on horse bridles, with alloy fastening. Screws ...
Mini Spares copy of the RAC/ Scottish works type-For serious off-road and rough stages, the only type to fit is the rounded sledge type front version, which helps ride the car over potentially damaging foreign bodies. Extra strengthening bar fits int...
true copies of the works canvass/felt type tool bag. As seen in books about ST Abingdon works cars. The last 2 left of these historic parts.
Never have a misted up front screen again. As used on Monte Carlo and other top Rally cars. 2 horizontal silver bands/element wires going across the screen a few inches from the top and 3.5 inches from bottom. Not suitable for twin point cars as the ...
Works Dash for RHD cars.
The later type more common dashes as used on the classic works Monte Minis and rally cars from ST Abingdon. Often seen in car magazines and competetion rally books.
Attaches to top and bottom parcel shelf r...
Rear screen seal for mk1 cars which had the smaller rear window 1959-1967.
The chrome moulding to fit the door bin on first 80 thousand MK1 minis with extra length tag with screw hole for location.
This is held on by screws but a single sided prong clips ADH3809 can be used in the centre - beware other...
10" blade MK1/2 with 6 sided nut for R/H/D or L/H/D with original 6 sided nuts. Right hand park, but you will have to disgard the nuts if you seek originality as after 1970 they became 8 sided or order correct kit for later type cars MSSK0...
Tank strap bracket welded to the rear of the boot floor which the single diagonal tank strap 21A2838 attaches to.
Angled spacer washer for Mk1/2 external door hinge cars for the upper hinge
Genuine Mini Spares product. The seal that goes on the neck of petrol tanks as protection against water intrusion and to also to make the hole look neater, so replace them when they crack or shrink through heat. This is the original fatter type as us...
FIA spec anchor plate for eye bolts, used when fitting harnesses. Sold individually, 7/16 UNF 65x65x3mm.
For MPI only when bonnet hook has been moved to central position.
This plate protects the bonnet lander panel from the hook and acts as a stiffener also. Stainless steel version.
This is the guide plate for the bonnet locking pin, now in stainless steel.
Cream crackle less mirror WITH ONE ARM and uses GFK7344 clip on one end,fitted from Oct 1964 to 1965
For the rear opening type quarter light, glass only in clear, MK3 ON.
Original shape washer jet for Mk1/2 minis. Made to the same specification as the last type made for rover parts sales with a nut on a loose thread so it can be tightened easily by hand in the engine bay without any modifications. Should be used with ...
The bracket fitted to the boot board and is not in any kits.
When a boot board is fitted the following brackets are required
14A9780x2 U shaped for the rear to hold the board
14A9781x2 side bracket with plug for board to si...
Upgraded L/H "A" panel for all Minis with internal hinges,1970 on.
A single wall panel has has a tendency to develop rust spots and is probably one of the most common panels replaced on the Mini.
Only available from Mini Spares th...
Upgraded R/H "A" panel for all Minis with internal hinges,1970 on.
A single wall panel has has a tendency to develop rust spots and is probably one of the most common panels replaced on the Mini.
Only available from Mini Spares th...
This very heavy duty bonnet strap is a excellent reproduction of the original factory Special Tuning department special. A copy of our Tan leather strap, but now available in black.
3.3mm thick from the tanneries for use on horse bridles,wit...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.