£90.78 exc vat
£108.94 inc vat
In stock
complete with brackets etc to fit to your hydrolastic mini. This was devised by special tuning abingdon to stop the wheels tramping and front to rear pitching of the cars. very worthwhile exercise for those of you left with \hydro cars to improve ride quality.
£90.78 exc vat
£108.94 inc vat
In stockRecommended usage 1 x C-AJJ3362 to fit one mini.
Fits top and bottom of the front damper and the lower rear damper to keep the bush from moving in the damper (shock absorber) eye sockets. 3/8"hole.
1.4mm thick by 24.6mm wide.
Upgraded, lower EN8 damper pin. 3/8"unf. Sold singly
Especially useful for competion cars or street cars with lowered suspension.
Its quite a good idea to change these if they are corroded to give a better seating for your dampers.<...
Replacement ball joint shims, comprising of 2x 003"(.076MM) shims, 2x 005"(.127MM) and 2 x 010"(.254MM).
one piece forged lower rod end arms
unbelievably at this price they are not the welded type as sold by many of our competitors
Same as the C-AJJ3360 lower arm kit, but includes the spherical rod ends,spacers and dustcov...
Angled grease nipple for the upper arm on the front suspension of all Minis
importantly lubricates the upper arm spindle which so often gets neglected so check yours out and make sure this nipple is working properly. Also fits rear radius ar...
The term 'hydro' in the renowned Cooper "S" suspension system "Hydro-lastic" means at least in part a liquid. This famous system was designed by BMC make for smooth and fluid ride while taking all of the abuse of off road rallying. It is not uncommon...
Mini Spares own to original drawing specifications with heat treatment correctly applied where appropiate.Lack of proper maintenance (grease) will make the pivot shaft and/or bearings wear that much faster. In severe cases the shaft may rust to the b...
The front tie rod on the Mini controls the fore and aft location of the lower front suspension arm of the car. In addition it provides a great degree of stability under braking. If your rod is bent or the bushes are worn then you need help. The Tie r...
Floor pan front to rear for the left hand side, only to the floor shape before rod change cars - ideal for MK1/2 restoration.
The weathered and cracked rubber you see is not actually the hydro displacer bag, but rather this rubber boot to protect it. Sold singly 1 required per displacer.
For Hydrolastic suspension cars, they were made with a 1/4" fixing hole but this needs elongating vertically to get the bump stop to sit properly on the upper arm which had different machine tolerances when manufactured.
Have you got one of the rare "wet" suspension Minis? This is the retainer plate that holds the protective sleeve around the hydro hose on the bulk head panel.
Sold singly 2 required per car.
Sold in pairs only.
These arms will give an extra 1.5 degrees extra negative camber over what the standard arms give on your car. To correct all variations of incorrect geometry found on the mini we have produced a pair of on car adjustable ...
Longer track rod end for running with negative camber, gives an extra 5mm of adjustment approximately over the standard item. Has consistent thread pattern and perfect design to our requirements to fits all known racks and classed as a competition tr...
Front hub nut that screws onto the CV joint of all early minis with drum brakes plus all standard cooper 997/8 models. 1 1/8, 1.125" AF nut size although 28mm width have been seen. The washer for this is 2A7323.
Fits top and bottom of the front damper and the lower rear damper to keep the bush from moving in the damper (shock absorber) eye sockets. 3/8"hole.
1.4mm thick by 24.6mm wide.
Same bump stop as fitted to MGB, this was utilised by ST Works Abingdon to go on their bump stop kits C-AJJ3313/4007 for hydrolastic minis. Sold singly.
The tie rods control braking stability and Caster! "Rose-jointed" end are the solid answer to total control! Sold with joints and in pairs. Not advised for general road use.
Original genuine standard tie bar bush (2 per rod) but sold individually.
These bushes are made to the original drawing and specifications by the original manufacturing company for BMC/Leyland & Rover.
These genuine bushes are soft ...
Dust cover for all four swivel pin joints. Sold individually.
Same on uppers or lowers this dust cover does get neglected but it does a tough job where it is positioned in keeping out the debris from the joint. If ever you are working on the...
Locktabs for under the steering arm bolts on all minis. Fits either side.
Sold individually
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.