EARLY MKI RALLY EXHAUST SYSTEM
C-ARA345

£450.00 exc vat

£540.00 inc vat

Out of stockOut of stock
MK1 original style Special Tuning works centre exit rally exhaust system, as fitted on Monte Carlo and early rally cars.

£450.00 exc vat

£540.00 inc vat

Out of stockOut of stock

People also bought products
MANIFLOW CENTRE EXIT SINGLE BOX 1.75" BORE EXHAUST...
C-ARA332SB

1.75" bore single box, centre exit exhaust system. This exhaust system by Maniflow is straighter and louder than our RC40 system. Very high quality with a skid plate on the bottom of the silencer and a polished stainless tip. Suitable for use with an...

£90.63 exc vat

£108.76 inc vat
MANIFOLD LCB EXHAUST STAGE 2 WITH SPECIAL CENTRE B...
C-AEG376

Standard bore road LCB (1-3/4"id) that has an enlarged and reshaped middle pipe which creates a type of vortex, simulating a pulsing effect similar to the outside two pipes,thus producing an improved BHP,Torque and power curve.Ideal for very hot smal...

£118.54 exc vat

£142.25 inc vat
STAINLESS STEEL LCB MANIFOLD - C-AEG365 (SSLM004)
C-AEG365S

Stainless steel Standard bore LCB (1-3/4"id) that is ideal for very hot small bore engines, for standard to high performance 1275s, and for street 1380s. And in stainless steel for long life!


There is NOT enough clearance room when fitti...

£221.27 exc vat

£265.52 inc vat
WASHER FOR MANIFOLD THICK TYPE
12A1211

The intake/exhaust manifold should be secured to the head with brass nuts and these very thick washers. These washers are intended to not only spread the clamping action but the thickness allows them to absorb the heat without deforming! Takes 4 per ...

£0.34 exc vat

£0.41 inc vat
MANIFOLD GASKET INLET / EXHAUST
AJM601

Manifold gasket fitted to all A series pre 1992 except Turbo which had a reinforced exhaust ports GUG704063MG and SPI from 199. From 1991 on a new better gasket with reinforced exhaust ports and backing was fitted GUG704053MG

£0.96 exc vat

£1.15 inc vat
RC40 EXHAUST FITTING KIT
RC40FK

Complete mounting kit for the RC40 exhaust. Includes all new rubber mounts, brackets and clamps.

£6.85 exc vat

£8.22 inc vat
GASKET FOR EXHAUST CATALYTIC CONVERTER
GEX7761

Metal gasket for the catalyst and is the same both ends for Cooper 1275CC RSP early cars, but only fitted on the front to later cars. If you cannot fit this gasket on the rear your car does not need one.

£0.67 exc vat

£0.80 inc vat
MANIFOLD STUD 6MM LONGER THAN 53K487 APPROX 1990 O...
LYR10028

Manifold stud for all A series injection engines and some late carburettor cars which is 45mm long-6mm longer than 53K487.carburettor engines usually retained the 53K487 shorter screw for the outside 2 holes.

Sold singly,6 per c...

£0.75 exc vat

£0.90 inc vat
MANIFOLD NUT SHORT BRASS 5/16" UNF
GFK3436

Standard brass manifold nut. You will probably want a mix of these and the longer 51K1177 to secure your intake/exhaust manifold. This nut 5/16" long whereas 51K1177 is 1"long.

£0.45 exc vat

£0.54 inc vat