£1,080.54 exc vat
£1,296.65 inc vat
In stock
£1,080.54 exc vat
£1,296.65 inc vat
In stockRecommended usage 1 x C-STR54SD to fit one mini.
Safety Devices FIA approved rear roll cage.
Comes in Black.
Black with mirror, optional colour aftermarket sun visor for Mk3 models which were thinner than pre 1965 cars for safety requirements. Will fit cars from December 1965 on. Check out the special clips to hold these visors as they are sold seperately ...
Universal to fit many vehicles and definately the mini for all Cobra seats but beware if your original seats lock down to the floor as a safety requirement. These do not lock down. The MOT testers in the UK could fail you if yours were originally th...
With headrest-this fixed back traditional bucket seat is the entry level
version of Cobra seats and has dep sides and a low back to ensure comfort and support without the restrictions of a larger seat. Black vinyl and no piping-
Fixed back for fast road this is Cobras New Clubman seat which still represents
good value with its massive leap in quality and design. Integral headpad and shoulder supports,deep sided bucketed supports,integral lumber support and four poin...
If your vehicle had a seat that locked to the floor it is an MOT requirement that you fit that type of fitting seat back in for safety requirements. This seat frame will allow you to fit the Cobra range of seats to your mini.
See [link]SEAT1...
Four tailor made felt pieces to fit in the segments between the bonnet strengthening webs to allow maximum under bonnet clearance.
See FELT860 for spray adhesive. These are about 1cm thick and the original very thick sound dea...
Moulded black carpet set for Rod change change with soundproofing attached where appropiate.
These fit correctly and snugly in your car over the tunnels etc for that professional look. 2 rubber front foot pads and on rear carpet has reinforc...
Headlamp switch fits MK1/2/ earlyY MK3, Toggle type also known as bat handle type, 3 POSITION. BLADE CONNECTIONS.
MK3 minis introduced a different headlining which was held up by rods rather than the MK1/2 type which were attached to a frame. There are five different colour codes on the 6 rods:
number 1 with red ends is EEB100060
n...
FIA certified and approved for motorsport it is lightweight and has compact styling. Slotted for use with competition seatbelts and the ultra strong construction has reinforced shoulder and side pads. In black, now comes with The option of using FIA ...
The lower brightwork moulding for finishing off the lower dash, crash pad rail or on earlier cars the painted metal surface of the panel which holds the switch panel section.See 14A8010 for clip
This moulding was fitted to all m...
Fitted for safety regulations to all MK2 minis from 1967-80 except Sweden and Canada to 1975 (not any MKI or van and pick up). Later commercial type minis did have it fitted with 3 clock speedo pod. This is a hard foam pad at the lower edge of the pa...
If your vehicle had a seat that locked to the floor it is an MOT requirement that you fit that type of fitting seat back in for safety requirements. This seat frame will allow you to fit the Cobra range of seats to your mini.
See [link]SEAT1...
This pump was fitted to the strange shaped, tall looking washer bottle GWW935 fitted under the bonnet with an integral fitted electric washer pump, fitted from 1990 until the location was changed to the boot area on single point injectio...
Rectangular switch for the rear heated screen with pin connectors plus a spade type. 3.1cm tall, from 1976 on.
HAZARD WARNING SWITCH, PIN TYPE CONNECTORS. MK4 FROM 1976. 3.1cm tall.
Late type swith carrier with 4 square holes plus heater and choke cable holes-uses the ratchet type choke cable with D shape fitting--earlier cars used round hole for pull and push chooke cableCZH3591
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.