DOOR HINGE R/H UPPER MK3
CZH202MS

£14.40 exc vat

£17.28 inc vat

In stockIn stock
Non genuine hinge for R/H upper on wind up window type doors with internal hinges from 1970on. See kit MSS017B for better price.

£14.40 exc vat

£17.28 inc vat

In stockIn stock

Recommended usage 1 x CZH202MS to fit one mini.
Wind up Window Doors - Qty 1

Recommended products

Countersunk, crosshead screw. 1/4"unf 19mm (3/4") total length.

This screw fits the internal door hinges on wind up window cars and the striker plate on the B post.

These shims are what the factory used to fit on the other side of the hinge panel as a stiffener and sometimes even to align the doors themselves, 2.2mm thick.

Door hinge shim for all wind up window cars, these are used to align the doors, 1.2mm thick and made in stainless steel use, with ALA6383 to get good door alignment See ALA6381 for thicker rear support plate.

Alternative products

R/H upper door hinge for MK3 on with internal door hinges and wind up window

also see kits MSSK017 and MSSK017B sets which are better value.

4 Non Genuine door hinges as a car set for wind up window type doors from 1970 on. These are a top quality item as opposed to the cheaper junk version available on the market.

Sold seperately as

top right CZH202MS 1 r...

Kit products

4 Non Genuine door hinges as a car set for wind up window type doors from 1970 on. These are a top quality item as opposed to the cheaper junk version available on the market.

Sold seperately as

top right CZH202MS 1 r...

People also bought products

High quality non genuine door check strap for MK3 cars with wind up window doors (use with retaining pin CLZ412). Beware there are cheap copies on the market that are poor quality and when fitted to our cars did not function correctly!

The gasket that sits behind the door stiker on all wind up window type minis

on the B post.

Stainless steel version of CZG5254 door striker plate. These used to be sided on earlier models but now fit either side. CZH627 striker plate lock with a loop fits into this. Supplied in pairs with stainless steel fixing scr...

Door hinge shim for all wind up window cars, these are used to align the doors, 0.7mm thick and made in stainless steel, use with ALA6382 to get good door alignment. See ALA6381 for thicker rear support plate.

MK3 door hinge fitting kit for all internal hinged doors. (hinges not included)

Door hinge shim for all wind up window cars, these are used to align the doors, 1.2mm thick and made in stainless steel use, with ALA6383 to get good door alignment See ALA6381 for thicker rear support plate.

Special thread cutting screw 1/4 UNF 1.25" (31mm) long.

Screw to hold the lock assembly on the door of MK3 cars with internal hinges and wind up windows. On new doors or for easy fitment use these special screws with cutting thread (3 sided ...

Full Mk2 door handle set with 2 front door locking handles and boot handle with matching keys. Fitted from 1966 with the intoduction of the door safety escutcheon boss. This boss is available as 24A1834 and gasket 24A1835.

Regre...

A great accessory for wind up window minis. Fitted in minutes to make such a difference driving your Mini with the window open. Wonderfull for those that smoke or love fresh air. In a tinted colour to stop bad reflections.

Twin point injection cars had a split seal system door frame seal for the front doors,the lower acting as a shield cover for the trim, fitted from chassis no BD134455 ON

Some customers have replaced it by the one piece CGA2835MS<...

Twin point injection cars had a split seal system door frame seal for the front doors,the lower acting as a shield cover for the trim. fitted from chassis no BD134455 ON

Some customers have replaced it by the one piece CGA2835MS<...

Special lower seal--fitted to MPI cars from October 1996 show cars chassis no BD134455 ON

Has a lip on inner edge to hold carpet back and tidy internal trim but other than that the CGA2835MS will fit --the full set is

Special lower seal--fitted to MPI cars from October 1996 show cars chassis no BD134455 ON

Has a lip on inner edge to hold carpet back and tidy internal trim but other than that the CGA2835MS will fit --the full set is

The rubber that sits in the frame to hold the windows on wind up window type doors. The frames are ALA5746/7 or see MSSK2105 also used on Clubman Estate and Traveller rear windows in the finger pull grips.

Sold individually.2 pe...

4 Non Genuine door hinges as a car set for wind up window type doors from 1970 on. These are a top quality item as opposed to the cheaper junk version available on the market.

Sold seperately as

top right CZH202MS 1 r...

Lower internal door hinge for either side.

Fits all wind up window type doors from 1970 on.

upper door hinge l/h for wind up window type door with internal hinge 1970on

this is not a genuine part and is available in a car set kit MSSK017B

See CZH203 for genuine

Genuine Mini Spares mouldings product as supplied to Rover.

These are the later door mouldings that prevent water running down the windows into the door causing rust and have the black platic ends fitted for later car safety regulations but ...

Multi purpose square plastic plug/nut for No8 screw size was used on many door fixings and fuse box to body.



Also suitable for Twin Point indicator fixings.

Sliding window type weatherstrip kit R/H

kit contains lower and upper sliding channels plus the vertical strip that attaches to the glass as a draught excluder plus the stainless steel window catch runner that the lower channel sits in,with ...