£33.02 exc vat
£39.62 inc vat
Out of stock
Left hand top hinge -wind up window type minis from 1970 on-- note -the studs actualy thread into the genuine hinge and can be replaced with a bolt if damaged or broken
£33.02 exc vat
£39.62 inc vat
Out of stock
Countersunk, crosshead screw. 1/4"unf 19mm (3/4") total length.
This screw fits the internal door hinges on wind up window cars and the striker plate on the B post.
These shims are what the factory used to fit on the other side of the hinge panel as a stiffener and sometimes even to align the doors themselves, 2.2mm thick.
Money saving car set of genuine hinges for wind up window type doors from 1970 on.
upper door hinge l/h for wind up window type door with internal hinge 1970on
this is not a genuine part and is available in a car set kit MSSK017B
See CZH203 for genuine
MK3 door hinge fitting kit for all internal hinged doors. (hinges not included)
Lower internal door hinge for either side.
Fits all wind up window type doors from 1970 on.
Non genuine hinge for R/H upper on wind up window type doors with internal hinges from 1970on. See kit MSS017B for better price.
Genuine Mini Spares mouldings product as supplied to Rover.
These are the later door mouldings that prevent water running down the windows into the door causing rust and have the black platic ends fitted for later car safety regulations but ...
Moulded shape type right hand door stay grommet fitted until 1985 when it was replaced by a flat sponge type seal CGE10038/9.
Genuine Mini Spares mouldings product as supplied to Rover.
Pair of the later door outer mouldings plus ADH3809 clips to help prevent water running down the windows causing rust.
These have black plastic ends for car s...
Moulded shape type left hand door stay grommet fitted until 1985 when it was replaced by a flat sponge type seal CGE10038/9.
Hinge for any mini with external hinges and uses gaskets BMP135 on A panel and and ALA7844 on door. Supplied with new studs/nuts and washers for fitment but if you need spares see 14A6818BOLT new set of bolts an...
door lock striker plate located on the B post of all wind up window minis
Mainly for MK3 cars, a perfect cosmetic addition to any mini are these tread plates. Supplied as a pair with self adhesive strips.
These shims are what the factory used to fit on the other side of the hinge panel as a stiffener and sometimes even to align the doors themselves, 2.2mm thick.
Also se kits MSSK017 and MSSK017B
Genuine lower hinge--note, the 2 studs actually thread into the genuine hinge so can be replaced if damaged or broken
Countersunk, crosshead screw. 1/4"unf 19mm (3/4") total length.
This screw fits the internal door hinges on wind up window cars and the striker plate on the B post.
Genuine Mini Spares mouldings product as supplied to Rover.
R/H outer brightwork trim with the seal attached to stop water seeping down into the door frame, on all cars with wind up windows from about 1980 on, these are the later type with t...
The pin that goes into the door stay check arm on the door itself on all minis with wind up type windows from 1970 to 2000.
Genuine door check strap for MK3 cars with wind up window doors.(use with retaining pin CLZ412 ). Beware! there are cheap copies on the market that are poor quality and when fitted to our cars did not function correctly.
Screw that holds on the exterior plastic type mirrors to the door, plus the handbrake fairlead guides on the floor of the car - also holds air vent nozzles to dash. 3/16" unf 3/4" long including head - for plain washer see WA1090.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.