£120.00 exc vat
£144.00 inc vat
In stock
Regret the plain non locking handle is obsolete.
£120.00 exc vat
£144.00 inc vat
In stockRecommended usage 1 x 24A2083KIT to fit one mini.
This screw is used to hold together the 2 halves of the disc shields on all
mini front discs. Also used to retain the boot lid cable to the bootlid.
Used on various door handles and door remote link.
This 3/16"unf screw was...
Do not forget to replace this little rubber seal that stops water getting into the boot lid via the handle hole. For sliding window type cars the door locks use ADA3817.
On mk3 models the small door gasket on the Mk3 wind up window door hand...
Seal for door handles MK1/2 and all sliding window exterior hinge cars.
also used on 14A7195 mk1 boot handlle used on mk1/mk2 and van/estate
is oval shaped
for boot / rear door use the hole at the rear ...
door locking handle for all MK2 minis with sliding windows. Thicker than the MK1 you should also have a safety boss 24A1834 fitted at the end of the handle on the door. The passenger door plain handle is no longer available but this will...
Complete fitting kit for the door check straps on all Minis fitted with external hinges.
Angled spacer washer for Mk1/2 external door hinge cars for the upper hinge
A great accessory for wind up window minis. Fitted in minutes to make such a difference driving your Mini with the window open. Wonderfull for those that smoke or love fresh air. In a tinted colour to stop bad reflections.
The rubber that sits in the frame to hold the windows on wind up window type doors. The frames are ALA5746/7 or see MSSK2105 also used on Clubman Estate and Traveller rear windows in the finger pull grips.
Sold individually.2 pe...
Non genuine hinge for R/H upper on wind up window type doors with internal hinges from 1970on. See kit MSS017B for better price.
Genuine Mini Spares mouldings product as supplied to Rover.
These are the later door mouldings that prevent water running down the windows into the door causing rust and have the black platic ends fitted for later car safety regulations but ...
Sliding window type weatherstrip kit R/H
kit contains lower and upper sliding channels plus the vertical strip that attaches to the glass as a draught excluder plus the stainless steel window catch runner that the lower channel sits in,with ...
Sponge type seal on L/H A post of all minis with wind up window type doors to protect from water running down into body. A part you must keep your eye on to stop rust.
Sponge type seal on R/H A post of all minis with wind up window type doors to protect from water running down into body. A part you must keep your eye on to stop rust, if the sponge is gettig hard then replace it.
Moulded shape type right hand door stay grommet fitted until 1985 when it was replaced by a flat sponge type seal CGE10038/9.
Holds the window regulator to the door on wind up window minis from 1970 on.
Also holds fog lamp bracket to rear valance. 1/4" unf with 1/2" thread on
panhead type screw.
Genuine MK3 wind-up window upper slide up and down felt lined channel that fits into the R/H upper door frame. Left (PAM3077) and right (PAM3076) look identical but are mirror images.
Genuine MK3 wind-up window upper slide up and down felt lined channel that fits into the upper door frame. Left (PAM3077) and right (PAM3076) look identical but are mirror images.If you are looking for a cheaper budget version see PAM3077MS
...
Genuine Mini Spares mouldings product as supplied to Rover.
These fit on the inside of the door as a draft excluder for the window, on all wind up window cars from 1970 on.
pair of outer door seal mouldings and fixing clips
These are the original type without the black plastic ends which were introduced on later models for safety criteria. All outside moudings are interchangable but are sided.
Genuine Mini Spares mouldings product as supplied to Rover.
Pair of the later door outer mouldings plus ADH3809 clips to help prevent water running down the windows causing rust.
These have black plastic ends for car s...
Sliding window type weatherstrip kit L/H
kit contains lower and upper sliding channels plus the vertical strip that attaches to the glass as a draught excluder
This kit contains one pin and one bush for repairing the external hinges on MK1/2 doors. If they are badly worn and you need Hinges see 14A6818/19/20/21.
If you require a new set of studs see 14A6818BOLT a complete car set in st...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.