£42.00 exc vat
£50.40 inc vat
In stock
£42.00 exc vat
£50.40 inc vat
In stockRecommended usage 1 x MSSK066 to fit one mini.
Screw to hold 14A6832 MK1/2 Striker plate.
Special 3/16" screw with a pointed end which helps locating when fitting, this has only 1/4" thread, a very short screw with countersunk head.
All minis with sliding type windows had this type of metal cover for the door striker plate.
The door striker plate on the B post holds the door shut, but the nylon guide block 14A6833 actually supports the weight when the door is closed. When one wears it typically takes the other with it, so replace both. Don't forget to order...
White plastic/nylon buffer on door of all UK external hinge minis.
The door striker plate 14A6832 holds the door shut, but the nylon guide block actually supports the weight when the door is closed. When one wears it typically...
The plate fits into the white 14A6833 door buffer to protect it from screw damage. Now made in stainless steel it is countersunk one side to take the screws.
The original bracket that the screws fixed to is no longer available a...
SPECIAL 6/32" UNC COUNTERSUNK POZI SCREW 1/4" LONG FOR HOLDING THE 14A6835 BUFFER PLATE TO BODY.
Special 6/32" UNC countersunk Pozidrive head screw 3/4" total length for holding the white nylon door buffer 14A6833.
Re-manufactured obsolete part now available to purchase. This is an item that often gets overlooked when rebuilding the doors. It accepts the screws that retain the nylon door guide dovetail. The drain tube also passes through it. Made from steel wit...
Sliding window catches chrome type for classic Mini MK1 & MK2, Traveller, Van, Countryman, Riley Elf and Wolseley Hornet.
Classic Minis and Mini Coopers had chrome metal catches for the sliding windows and channels. Black and white...
Upper door moulding rivet for Cooper S door trim. For Mk1 usually 1 at front and 3 at back making 4 per side and on Mk2 there were 2 per end at bottom making 4 per side. This is the 10mm head rivet and not required on our own 14A9773/9774 trims that ...
High quality non genuine door check strap for MK3 cars with wind up window doors (use with retaining pin CLZ412). Beware there are cheap copies on the market that are poor quality and when fitted to our cars did not function correctly!
Complete fitting kit for the door check straps on all Minis fitted with external hinges.
Angled spacer washer for Mk1/2 external door hinge cars for the upper hinge
SPECIAL 6/32" UNC COUNTERSUNK POZI SCREW 1/4" LONG FOR HOLDING THE 14A6835 BUFFER PLATE TO BODY.
Full Mk2 door handle set with 2 front door locking handles and boot handle with matching keys. Fitted from 1966 with the intoduction of the door safety escutcheon boss. This boss is available as 24A1834 and gasket 24A1835.
Regre...
Van, Clubman Estate, Traveller and Countryman rear door hinge gasket. (sold individually)
Sliding window type weatherstrip kit R/H
kit contains lower and upper sliding channels plus the vertical strip that attaches to the glass as a draught excluder plus the stainless steel window catch runner that the lower channel sits in,with ...
Sponge type seal on L/H A post of all minis with wind up window type doors to protect from water running down into body. A part you must keep your eye on to stop rust.
Sponge type seal on R/H A post of all minis with wind up window type doors to protect from water running down into body. A part you must keep your eye on to stop rust, if the sponge is gettig hard then replace it.
Holds the window regulator to the door on wind up window minis from 1970 on.
Also holds fog lamp bracket to rear valance. 1/4" unf with 1/2" thread on
panhead type screw.
Sliding window type weatherstrip kit L/H
kit contains lower and upper sliding channels plus the vertical strip that attaches to the glass as a draught excluder
This kit contains one pin and one bush for repairing the external hinges on MK1/2 doors. If they are badly worn and you need Hinges see 14A6818/19/20/21.
If you require a new set of studs see 14A6818BOLT a complete car set in st...
This is the classic upgrade of the '60s. Steel wire checkstraps" will actually hold your MKI/MKII doors open. Sold per pair.
Sliding window Mini models all must now use these black plastic locks for the windows. Our special kit includes a complete set of all the pieces: 4 latches, rubber seals, screws and chrome nuts.This kit is a great saving over buying all the parts ind...
These Mirrors are made in the U.K. by Tex. Slightly convex lens gives excellent rearward visibility. Right side, left is GAM218A. For fitment to laters cars originally fitted with plastic mirrors, use fitting kit M90999.
See als...
Genuine Mini Spares product-These are copies of the original solid type, with stronger reinforced internal wire and with the holes for drainage and securing.
These fit either side door where the holes line up on the window catch moulding. C...
The plate fits into the white 14A6833 door buffer to protect it from screw damage. Now made in stainless steel it is countersunk one side to take the screws.
The original bracket that the screws fixed to is no longer available a...
Perhaps one of the most endearing features of the early Minis with sliding windows are the external door hinges, that is until they are worn beyond repair and sag to the point that the door won't close. Replacements are available individually, but th...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.