DOOR HANDLE OUTER LOCKING FROM 1966/MK 2
24A2083

£30.64 exc vat

£36.77 inc vat

In stockIn stock
door locking handle for all MK2 minis with sliding windows. Thicker than the MK1 you should also have a safety boss 24A1834 fitted at the end of the handle on the door. The passenger door plain handle is no longer available but this will fit either side and if you prefer all key numbers the same a complete kit of 2 handles and boot handle are available as 24A2083KIT

These handles used to have a self thread cutting No8 screw but the holes in the handle are now metric or about No12 self tap,

Does not come with Escutcheons

£30.64 exc vat

£36.77 inc vat

In stockIn stock

Recommended usage 1 x 24A2083 to fit one mini.
Front Door - Sliding window type - Qty 1

Recommended products

Chrome on alloy this Right hand escutcheon is fitted against the door for the opening exterior handle to fit and lock in. The rubber seal between this and the door is ADA3817 to stop rusting of the door

Seal for door handles MK1/2 and all sliding window exterior hinge cars.

also used on 14A7195 mk1 boot handlle used on mk1/mk2 and van/estate



is oval shaped



for boot / rear door use the hole at the rear ...

Chrome on alloy this Left hand escutcheon is fitted against the door for the opening exterior handle to fit and lock in. Fitted to all sliding window type doors.The rubber seal between this and the door is ADA3817 to stop rusting of the ...

Alternative products

Full Mk2 door handle set with 2 front door locking handles and boot handle with matching keys. Fitted from 1966 with the intoduction of the door safety escutcheon boss. This boss is available as 24A1834 and gasket 24A1835.

Regre...

People also bought products

Sliding window catches chrome type for classic Mini MK1 & MK2, Traveller, Van, Countryman, Riley Elf and Wolseley Hornet.



Classic Minis and Mini Coopers had chrome metal catches for the sliding windows and channels. Black and white...

Upper door moulding rivet for Cooper S door trim. For Mk1 usually 1 at front and 3 at back making 4 per side and on Mk2 there were 2 per end at bottom making 4 per side. This is the 10mm head rivet and not required on our own 14A9773/9774 trims that ...

Complete fitting kit for the door check straps on all Minis fitted with external hinges.

Angled spacer washer for Mk1/2 external door hinge cars for the upper hinge

This stainless steel plate has recessed holes in for the check strap screws.

2 per door are required and these are only for cars with external hinges that had the material check strap as per MK1.2 and vans

Mk3 on Mini (all internal hinged models) inner door frame bottom drain hole repair section with outer skin lip for the R/H door, had 3 drain holes also see part number MS34L for the repair for the bottom of the door.

Technicall...

Mk3 on Mini (all internal hinged models) inner door frame bottom drain hole repair section with outer skin lip for the L/H door, also see part number MS34L for the repair for the bottom of the door.

Technically you cannot fit b...

SPECIAL 6/32" UNC COUNTERSUNK POZI SCREW 1/4" LONG FOR HOLDING THE 14A6835 BUFFER PLATE TO BODY.

Full Mk2 door handle set with 2 front door locking handles and boot handle with matching keys. Fitted from 1966 with the intoduction of the door safety escutcheon boss. This boss is available as 24A1834 and gasket 24A1835.

Regre...

New set of metric studs, bolts, nuts and washers as supplied with the alloy external hinge kit (PEASE NOTE: This kit is NOT suitable for the original hinges). The studs have allen key socket ends to help put them into the hinge easily without damage,...

Twin point injection cars had a split seal system door frame seal for the front doors,the lower acting as a shield cover for the trim, fitted from chassis no BD134455 ON

Some customers have replaced it by the one piece CGA2835MS<...

Twin point injection cars had a split seal system door frame seal for the front doors,the lower acting as a shield cover for the trim. fitted from chassis no BD134455 ON

Some customers have replaced it by the one piece CGA2835MS<...

4 Non Genuine door hinges as a car set for wind up window type doors from 1970 on. These are a top quality item as opposed to the cheaper junk version available on the market.

Sold seperately as

top right CZH202MS 1 r...

Non genuine R/H repair section

for wind up window type doors this is the lower 2-3" of the inner skin and the bottom of the door section that usually rusts out-includes a lip section where the outer skin flaps overlaps for fitment--new panel...

Non genuine L/H repair section

for wind up window type doors this is the lower 2-3" of the inner skin and the bottom of the door section that usually rusts out-includes a lip section where the outer skin flaps overlaps for fitment--new panel...

These Mirrors are made in the UK by Tex. Slightly convex lens gives excellent rearward visibility. Left side. Right is GAM217. For fitment to laters cars originally fitted with plastic mirrors, use fitting kit M90997. See also

G...

Multi purpose square plastic plug/nut for No8 screw size was used on many door fixings and fuse box to body.



Also suitable for Twin Point indicator fixings.

Sliding window type weatherstrip kit R/H

kit contains lower and upper sliding channels plus the vertical strip that attaches to the glass as a draught excluder plus the stainless steel window catch runner that the lower channel sits in,with ...

Sponge type seal on L/H A post of all minis with wind up window type doors to protect from water running down into body. A part you must keep your eye on to stop rust.