SELF TAPPING SCREW FOR DOOR LOCK CONTROL
PTZ804

£0.14 exc vat

£0.17 inc vat

In stockIn stock

£0.14 exc vat

£0.17 inc vat

In stockIn stock

Recommended usage 1 x PTZ804 to fit one mini.

People also bought products

MK3 Door & boot handle fitting kit, including original type screws, star washers and gaskets.

Key barrel set for Mk3 onwards door handles and boot handles.

Full Mk1 door handle set with 2 front door locking handles and boot handle with matching keys.

For wind up window type doors this is the mini saloon and clubman estate r/h

door lock mechanism mounted on the door.

For wind up window type doors this is the mini saloon and clubman estate l/h

door lock mechanism mounted on the door.

A complete set of 2 front door and one boot handle in chrome all with the same key numbers for wind up window door minis 1970on (keys included).

Door Handle Gasket's should also be replaced at same time, CZH1729 and [link]ALA579...

If your MKI or MKII suffers from terminal "door handle sag" it is quite possible that the inside door latch mechanisms are tired. A left hand drive car should have a locking latch on the right side (the driver's side key-locks with the handle). Right...

If your MKI or MKII suffers from terminal "door handle sag" it is quite possible that the inside door latch mechanisms are tired. A left hand drive car should have a locking latch on the right side (the driver's side key-locks with the handle). Right...

If your MKI or MKII suffers from terminal "door handle sag" it is quite possible that the inside door latch mechanisms are tired. A left hand drive car should have a locking latch on the right side (the driver's side key-locks with the handle). Right...

If your MKI or MKII suffers from terminal "door handle sag" it is quite possible that the inside door latch mechanisms are tired. A left hand drive car should have a locking latch on the right side (the driver's side key-locks with the handle). Right...

Seal for door handles MK1/2 and all sliding window exterior hinge cars.

also used on 14A7195 mk1 boot handlle used on mk1/mk2 and van/estate



is oval shaped



for boot / rear door use the hole at the rear ...

The door striker plate on the B post holds the door shut, but the nylon guide block 14A6833 actually supports the weight when the door is closed. When one wears it typically takes the other with it, so replace both. Don't forget to order...

clip that sits on the activating lever on the bottom of the MK3 door handle itself.

New door handles CZH886 and CZH887 have this clip on already.

On sliding window type MK1/2 doors the door locks are held on by these 3 screws.

3/16"unf countersunk head 1" long.

Clip to connect the door opening remote control rod plus the lock control mechanism fits on CZH640/1 and CZH616/7-- 2 per door. Also fits the wastegate on turbo models.

Sliding window catches chrome type for classic Mini MK1 & MK2, Traveller, Van, Countryman, Riley Elf and Wolseley Hornet.



Classic Minis and Mini Coopers had chrome metal catches for the sliding windows and channels. Black and white...

Upper door moulding rivet for Cooper S door trim. For Mk1 usually 1 at front and 3 at back making 4 per side and on Mk2 there were 2 per end at bottom making 4 per side. This is the 10mm head rivet and not required on our own 14A9773/9774 trims that ...

High quality non genuine door check strap for MK3 cars with wind up window doors (use with retaining pin CLZ412). Beware there are cheap copies on the market that are poor quality and when fitted to our cars did not function correctly!

The gasket that sits behind the door stiker on all wind up window type minis

on the B post.