£93.90 exc vat
£112.68 inc vat
Special order
£93.90 exc vat
£112.68 inc vat
Special orderRecommended usage 1 x FS007R to fit one mini.
You can spend hours cutting out rust and patching holes, but why bother? These reproduction floor pans extend the full width with vertical flanges for easy installation, and fairly well represent the original stamping. They have added metal to includ...
Complete fitting kit for the door check straps on all Minis fitted with external hinges.
Front subframe fitting kit for pre 76 twin bolt subframes, locktabs are included but not the subframe tower spacers as these rarely need changing.
Complete set of bolts to mount the front subframe on all post 76 single bolt subframes less the large tower bolts and towing eye, enough fixings are supplied for those who wish not to use a towing eye.
Angled spacer washer for Mk1/2 external door hinge cars for the upper hinge
Van L/H full length half floor. You can spend hours cutting out rust and patching holes, but why bother? These reproduction floor pans extend the full width and length-plain pressed floor with indents but no carpet brackets or lugs underneath
Repair section of bottom of door for external hinge cars, MK1/2.
This crude non genuine parts is the only repair section available for early doors apart from door skins.Lots of stretch marks and wrinkles but they have been fitted by customer...
Non genuine R/H Van inner sill. Only made as an after market replacement as no genuine part was ever available seperately. Best one on the market for a comlplete inner sill replacement panel. For Mk1 VAN
Non genuine L/H Van inner sill. Only made as an after market replacement as no genuine part was ever available seperately. Best one on the market for a comlplete inner sill replacement panel. For Mk1 VAN
Genuine Mini Spares product. The seal that goes on the neck of petrol tanks as protection against water intrusion and to also to make the hole look neater, so replace them when they crack or shrink through heat. This is the original fatter type as us...
Tailgate pin and chain for all pickup models, sold individually, 2 required per car.
This kit contains all the floor brackets and mounts required for fitting Minis with 7.5 gallon tank 10/12" wheels or with 165 profile tyres.
The boot board bracket 14A9783 is not included
For 10" wheels with 145 tyres ...
A post and inner wing repair panel 8" wide for Mk1/2 saloon and MK1 Van/pickup
R/H side--6" from a post section
A post and inner wing repair panel 8" wide for Mk1/2 saloon and MK1 Van/pickup
L/H side-6" from A post section
The bracket fitted to the boot board and is not in any kits.
When a boot board is fitted the following brackets are required
14A9780x2 U shaped for the rear to hold the board
14A9781x2 side bracket with plug for board to si...
O/S/F wing t for 1996 on cars. THIS WING STILL NEEDS MODIFYING to allow for fitting of Sportspac arches and 13" wheels. After trimming/cutting to size remember to replace or renew the stiffener lip ALR360380
Has the headlamp re...
Called the rear bonnet seal it actually sits in the windscreen front scuttle panel on all minis up to 1991. This is the shape and size neoprene foam seal that we have found works best and has an adhesive backing to make fitting easier and less messy.
Slat type front grille section for mini van which will need trimming before welding into recess of either an original damaged front panel or a saloon version.
It is sold as a grille size panel and can be fitted as such when painted with [li...
The first panel up towards the dash after the floor pans, at an angle and where steering rack bolts to floor without any brackets or fittings, see also same panel with steering rack fitting AHA36006 for 1976 on rubber mounted subframe or...
Stiffener for inner sill for Van with metal load floor and Pickup L/H
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.