£16.04 exc vat
£19.25 inc vat
In stock
£16.04 exc vat
£19.25 inc vat
In stockRecommended usage 1 x GLP141 to fit one mini.
Universal paper oil pump gasket for all A series engines. Fits between pump and block. See GUG705560GM for genuine.
Converted into a non melting type grease.Favoured by proffessionals for camshaft,lobes and lifter,and any valvetrain to stop scuffing on start up. Also useful for oil pumps to stop drain back on start up
Converted into a non melting type grease.Favoured by proffessionals for camshaft,lobes and lifter,and any valvetrain to stop scuffing on start up. Also useful for oil pumps to stop drain back on start up
Original short pin drive oil pump for all Pre A Plus minis with 850/998/1100cc engines except autos and others with star drive or the later slot drive pumps as found on A Plus blocks.
Competition Slot drive pump for 1300cc A-Plus engines.
Almost all oil pumps available today have the same design capacity. The problem is the lack of precise manufacturing. Most factories in their quest for production volume have sacrificed ...
Slot drive pump for 998cc A-Plus engines.
All oil pumps are not created equal! Almost all pumps available today have the same design capacity. The problem is the lack of precise manufacturing. Most factories in their quest for production vol...
Turbo oil pump, highest flow available. 9 Gallons per minute as against approx 6 GPM. This pump is a late model slot drive and will fit into any 1275cc engine and exactly the same as the second generation of pump as sold by Unipart/Rover.
Ga...
A low oil pressure warning light switch is available to help protect the engine. The standard one comes on at 7lb-much too late to avoid damage. This one comes on at 20lb and is adjustable up to 120lb. Please note this is now a twin terminal switch, ...
3 Bolt hole fixing pump for A plus 998cc engines. This has a spade type drive spindle to fit the slot in the camshafts. This replaced earlier peg type drive which fitted into camshafts with a pin (known as pin drive).
The "slot" drive oil pump has been the factory standard for many years. The evolution of the pump in production was started with the "pin" drive that is most common in early small bore motors. These pumps have a fork on the drive side to engage the "...
Timing cover front plate and tensioner plate bolt and washer kit. Comes with all parts to fit the cover except for the counter sunk screws if fitting a duplex kit (our duplex kits all come with these).
This is the large seal for the early type oil filter assembly pre spin on type.
These Swiftune die cast performance pistons are part of their new Heritage range and are manufactured by global leading F1 German piston manufacturer Mahle. These pistons have been developed using their 50 plus years of experience. Glyn Swift was usi...
These Swiftune die cast performance pistons are part of their new Heritage range and are manufactured by global leading German F1 piston manufacturer Mahle. These pistons have been developed using their 50 plus years of experience.
Glyn Swif...
These Swiftune die cast performance pistons are part of their new Heritage range and are manufactured by global leading F1 German piston manufacturer Mahle. These pistons have been developed using their 50 plus years of experience. Glyn Swift was usi...
You should replace the camshaft bearings every time the block goes to the machine shop. These bearings fit all late model 1275cc blocks (the ones without tappet covers on the back) It's almost too simple and thus often overlooked during a rebuild. Ca...
Race quality Single piston ring pack for Mini Spares Evolution Pistons which also fits Mega and Omega pistons. This uses 3 piece oil ring 4mm and 2 of 1.2mm compression ring.
Sold per piston so 4 packs required per engine.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.