£225.60 exc vat
£270.72 inc vat
In stock
£225.60 exc vat
£270.72 inc vat
In stockRecommended usage 1 x MDM266 to fit one mini.
Converted into a non melting type grease.Favoured by proffessionals for camshaft,lobes and lifter,and any valvetrain to stop scuffing on start up. Also useful for oil pumps to stop drain back on start up
A vital aid for accurate valve timing this disc is a 360 degree protractor disc made by kent cams.
Genuine Mini Spares camshaft,great for all road uses- A Plus slot drive only.
Valve clearance should be 0.014" on inlet and 0.016" exhaust. LCA 107 degree
DURATION INLET 264 EXHAUST 268, LIFT INLET 264 EXHAUST 289.
This ca...
Supplied to order. Truly a lovely road going camshaft with a little more torque and oomph originally than SW5 or EVOLUTION002 and now over shadowed by so many alternatives these days. With 252 duration on inlet and exhaust-same as SW5.
Proper timing of the camshaft is very important and while it is easy and nice to do it with a precise adjustable cam sprocket it is also cheap to do it with offset cam keys. 1 or 2 degrees difference in cam timing can make a difference in performance...
Proper timing of the camshaft is very important and while it is easy and nice to do it with a precise adjustable cam sprocket it is also cheap to do it with offset cam keys. 1 or 2 degrees difference in cam timing can make a difference in performance...
Proper timing of the camshaft is very important and while it is easy and nice to do it with a precise adjustable cam sprocket it is also cheap to do it with offset cam keys. 1 or 2 degrees difference in cam timing can make a difference in performance...
Proper timing of the camshaft is very important and while it is easy and nice to do it with a precise adjustable cam sprocket it is also cheap to do it with offset cam keys. 1 or 2 degrees difference in cam timing can make a difference in performance...
Proper timing of the camshaft is very important and while it is easy and nice to do it with a precise adjustable cam sprocket it is also cheap to do it with offset cam keys. 1 or 2 degrees difference in cam timing can make a difference in performance...
Proper timing of the camshaft is very important and while it is easy and nice to do it with a precise adjustable cam sprocket it is also cheap to do it with offset cam keys. 1 or 2 degrees difference in cam timing can make a difference in performance...
Proper timing of the camshaft is very important and while it is easy and nice to do it with a precise adjustable cam sprocket it is also cheap to do it with offset cam keys. 1 or 2 degrees difference in cam timing can make a difference in performance...
Genuine Mini Spares camshaft,great for all road uses- A Plus slot drive only.
Valve clearance should be 0.014" on inlet and 0.016" exhaust. LCA 107 degree
DURATION INLET 264 EXHAUST 268, LIFT INLET 264 EXHAUST 289.
This ca...
woodruff key to fit in the camshaft to hold the larger timing chain gear. See 6K836 for the crankshaft keyway for the lower smaller timing chain gear
Replace with new camshaft,it's almost too easy to overlook during a rebuild. Camshaft bearings are pressed into the block and thus are usually done by a machine shop. You would not rebuild an engine without replacing the rod bearings, so why not the ...
The only upgrade in camshaft you can get away with on the single point injection cars without changing ECU etc--A mild road cam
As of July 2007 Kent cams have no supply of old camshafts for reprofiling and we will only supply camshafts fro...
Proper timing of the camshaft is very important and while it is easy and nice to do it with a precise adjustable cam sprocket it is also cheap to do it with offset cam keys. 1 or 2 degrees difference in cam timing can make a difference in performance...
Slightly lumpy at idle, especially in small bore units. Strong mid and top end power. Rev band 1,500 - 7,000 rpm.
As of July 2007 Kent cams had no supply of old camshafts for reprofiling and now only supply camshafts from new blanks.
Converted into a non melting type grease.Favoured by proffessionals for camshaft,lobes and lifter,and any valvetrain to stop scuffing on start up. Also useful for oil pumps to stop drain back on start up
Lightened cam gear duplex timing gear and chain set. Not recommended for race/rally applications. approx 69-70g 9% lighter
General: Camshaft Drive Systems
For highly tuned engines always use steel duplex as cast is nowhere as st...
Standard weight, 44.00grams, follower with oil drain hole. Always check for wear and replace whenever a new camshaft is fitted. These are manufactured by the supplier to AE Hepolite the original engine components manufacturer and should be coated wit...
MD266 in A plus form with cam followers.valve springs and initial set up oil.
For timing disc, order separately as C-AJP337
As of July 2007 Kent cams have no supply of old camshafts for reprofiling a...
If you are replacing your timing chain or just doing routine maintenance a new locktab is sure to come in handy.
Standard cast duplex gear set from the original AE supplier. for road use only.
Found to be the best fitting in Mini Mag feature Autumn 2007.
Driving the cam and controlling the timing relationships between the cam and the crank i...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.