£32.00 exc vat
£38.40 inc vat
Out of stock
£32.00 exc vat
£38.40 inc vat
Out of stock
For 850, 998, 1100 cylinder heads where there is no sandwich plate under the thermostat housing.
Fits from the thermostat housing and end manifold stud. The other end bolts to the bulkhead where the heater hoses go through the body.
Lower Stabilizer Kit, RH.
Designed as an almost mandatory addition to any Mini with a rod change transmission, extra stabilizers will greatly aid any car. In stock form the control is left to the upper stabilizer. This often results in not o...
Mahle was Vandervell bearings 1.064" 27.05mm wide mains for the late 850cc plus all 997/998/1100cc at standard size. Early 850 mains were VP592 and 1.185" 30.10mm wide..Quantity required-1 set.
A series mini engine crank pulley bolts have been known to come loose, caused by pulley damper vibration on competition engines. This is a high tensile longer extended thread cap head bolt with thick washer to rectify this problem and also allow furt...
Set of 8, original leyland ST product but now made for us to our specification. Critical to the life and performance of the camshaft is the use of high quality cam followers. Remember, they operate in a finite hole and thus the dimensional tolerances...
All "A" Plus and engines with metal tube to locate dipstick (no 850cc or Automatics). 227mm from mount face to full mark.
A design initiated by Keith Dodd as an easier to use alternative to the other engine oil dip sticks available with butt...
Universal paper oil pump gasket for all A series engines. Fits between pump and block. See GUG705560GM for genuine.
Mini Spares own Universal gasket set.
This engine block gasket set fits all manual blocks and include rubber tappet chest covers and bolt seals, also including A plus and Pre A Plus timing gear and cover gaskets. For the equivalent gasket se...
Adjustable cam gear set with non stretch chain. Cam gear weighs 674g
Even a stock camshaft needs to be timed correctly. If you want to get the maximum benefit from a "hot" cam it is doubly important that the cam timing be correct. This adju...
Countersunk screw for holding the front palte to the crankshaft bearing cap on cars fitted with duplex gears to give the clearance required. 2 required per car.
Lower Stabilizer Kit, LH.
Designed as an almost mandatory addition to any Mini with a rod change transmission, extra stabilizers will greatly aid any car. In standard form the engine control is left to the upper stabilizer. This often result...
A low oil pressure warning light switch is available to help protect the engine. The standard one comes on at 7lb-much too late to avoid damage. This one comes on at 20lb and is adjustable up to 120lb. Please note this is now a twin terminal switch, ...
Oil pressure relief valve ball and spring kit. Cooper S upto 1971. Can be retro fitted to all minis to boost oil pressure.
All "A" Plus and engines with metal tube to locate dipstick (not 850cc or Automatics). Stainless dipstick is the fancy of fancy and you can even have your choice of colours on the knob as long as it is red or blue!
MSA1124 (Blue) or [lin...
The oil pressure relief valve consists of an aluminum plunger with a heavy spring behind it. Access is through the 15/16" domed cap nut beside the dizzy. Once this nut is removed the spring will be visible. The plunger is beneath the spring and will ...
This pin holds the tensioner 12G2628 for cars with single chain timing gears from 1980 on. You can tell if your car has this set up because the timing cover has a large bulge to accommodate this set up. Started on engine numbers 99H791 9...
This is the metal plate to blank off the mechanical pump hole on the engine block. No longer available from Rover but Mini Spares have them.
Mini cork Rocker cover gasket, suitable for all Minis and A series engines except those with 11 stud heads (see part number GUG5038VC). A must have replacement item when adjusting rocker clearances. see GUGG705009EVO for sil...
The original stabiliser kit with cone shaped spacers to strengthen up the rubber bushes against engine movement. Kit includes 4 cone plastic shaped inserts and 4 bushes. The cone shaped inserts push the rubber out in the middle of the engine steady b...
These are sold per bush but fitted in pairs.
Apart from very early cars all minis up to 1996 had 2 of these each end.
From 1996 rover fitted a single silent block type bush which will fit your existing 21A1109 arm (par...
Originally marketed by Minispares in the mid 70s so many companies copied them because of their smart looks and ease of fitment. These have been improved by offsetting the arms to help tighten plus stop the arm falling out when they were straight. Ki...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.