GEARBOX STABILISER L/H KIT
MSSK001

£18.88 exc vat

£22.66 inc vat

In stockIn stock
Lower Stabilizer Kit, LH.

Designed as an almost mandatory addition to any Mini with a rod change transmission, extra stabilizers will greatly aid any car. In standard form the engine control is left to the upper stabilizer. This often results in not only significant movement but even a cracking and breaking of the bracket that is welded to the bulkhead.

This kit fits on the left side and connects to the lower front gearbox case studs/bolts and goes rearward to bolt on the rear leg of the subframe, where one hole will be required.

The bushes used are the stock bushes as used in the stock upper stabilizer. Kits are made for both the right or left side of the tranny; either or both can be used. (See MSSK which fits to the lower clutch casing/flywheel case studs and then goes rearward to bolt on the rear leg of the subframe, where one hole will be required.)

CRC5329POLY uprated bushes can be bought also to uprate the fit further

£18.88 exc vat

£22.66 inc vat

In stockIn stock

Recommended usage 1 x MSSK001 to fit one mini.
Engine Mountings - Qty 1
Front Rubber Cone Spring Suspension ( Known as Dr - Qty 2

Kit contained products

Used in our MSSK001 left hand lower engine stabiliser kit this bracket fits to the subframe and the gearbox.

Lower left hand rod fitted to the gearbox and facing backwards to the subframe as an engine stabiliser is part of our complete kit MSSK001.

People also bought products

AC Dodd Road Sport camshaft, ideal for those wanting the most from a tourer cam whilst still have a smooth idle. Please see picture for full cam specs.



Road Sport, For those requiring the maximum from a tourer cam, excellent road m...

Replace with new camshaft,it's almost too easy to overlook during a rebuild. Camshaft bearings are pressed into the block and thus are usually done by a machine shop. You would not rebuild an engine without replacing the rod bearings, so why not the ...

Steel ring set,for 4 ring pistons. 3 compression rings @ 0.0625" oil rings 0.125 as per original 998 pre A plus and 1098cc versions inc morris minor and sprite range.

Timing cover front plate and tensioner plate bolt and washer kit. Comes with all parts to fit the cover except for the counter sunk screws if fitting a duplex kit (our duplex kits all come with these).

11/16" dowty seal for post 1991 cars where the original pipe has been replaced with a braided pipe or an oil cooler has been fitted using part number MOC4. used on the TCZ102

This is the large seal for the early type oil filter assembly pre spin on type.

These Swiftune die cast performance pistons are part of their new Heritage range and are manufactured by global leading F1 German piston manufacturer Mahle. These pistons have been developed using their 50 plus years of experience. Glyn Swift was usi...

These Swiftune die cast performance pistons are part of their new Heritage range and are manufactured by global leading German F1 piston manufacturer Mahle. These pistons have been developed using their 50 plus years of experience.

Glyn Swif...

These Swiftune die cast performance pistons are part of their new Heritage range and are manufactured by global leading F1 German piston manufacturer Mahle. These pistons have been developed using their 50 plus years of experience. Glyn Swift was usi...

Replacement O ring for the Minispares range of chrome dipticks

You should replace the camshaft bearings every time the block goes to the machine shop. These bearings fit all late model 1275cc blocks (the ones without tappet covers on the back) It's almost too simple and thus often overlooked during a rebuild. Ca...

Race quality Single piston ring pack for Mini Spares Evolution Pistons which also fits Mega and Omega pistons. This uses 3 piece oil ring 4mm and 2 of 1.2mm compression ring--sold per piston so 4 packs required per engine

Main bearings plus 60 oversize, 1275 2" mains. 60 thou oversize. Heavy duty steel backed bearing for durability and long life. The bearings to use if you want it to last. The only bearings to use on a fast road motor.



Sintered copp...

Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.



Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...

ACL Race Bearings



ACL Race series bearings are precision manufactured to a wall thickness of ±0.0040mm giving engine builders close control of vertical oil clearance.

What is the purpose of ACL Race series bearings?
...

ACL Race Bearings



ACL Race series bearings are precision manufactured to a wall thickness of ±0.0040mm giving engine builders close control of vertical oil clearance.

What is the purpose of ACL Race series bearings?
...

ACL Race Bearings



ACL Race series bearings are precision manufactured to a wall thickness of ±0.0040mm giving engine builders close control of vertical oil clearance.

What is the purpose of ACL Race series bearings?
...