£0.78 exc vat
£0.94 inc vat
In stock
Apart from very early cars all minis up to 1996 had 2 of these each end.
From 1996 rover fitted a single silent block type bush which will fit your existing 21A1109 arm (part number usually stamped on arm) later 1275cc cars had a longer bar 21A1817 fitted where the engine was moved forward.
There is also a poly version available as CRC5329POLY.
£0.78 exc vat
£0.94 inc vat
In stockRecommended usage 4 x CRC5329 to fit one mini.
Engine stabiliser arm to block bolt. This is the longer bolt that fits the engine stabiliser rod to the cylinder block.
The metal sleeve in the engine stabiliser bar at the engine end for the two rubber bushes to sit on. Also useful as the spacer between the DAM5992 bracket and the clutch on A plus engines.
The last Rover update on the upper engine stabiliser bar.
A one piece silent block type bush was fitted at both ends from 1996 on and will fit any cars that have 2 bushes fitted at either end as original.
These have also been fitted...
This bush is a genuine version of CRC5329 and sold individually.
There are 2 of these bushes fitted at either end of the engine stabiliser on all cars upto 1996 except some very early cars which had large single bushes fitted. F...
The original stabiliser kit with cone shaped spacers to strengthen up the rubber bushes against engine movement. Kit includes 4 cone plastic shaped inserts and 4 bushes. The cone shaped inserts push the rubber out in the middle of the engine steady b...
The original stabiliser kit with cone shaped spacers to strengthen up the rubber bushes against engine movement. Kit includes 4 cone metal shaped inserts and 4 bushes. When stocks run out only the plastic insert type kit SBK1 will be ava...
Crankshaft washers for crankshaft at 3 thou oversize on each one
sold as a set of four for 998 and 1100cc.
A kit to convert the early style cartridge oil filter to the later style spin on filter.
Engine mount bolt kit for manual cars, 1 kit requried per car.
Victor Reinz/Mahle small bore head gasket for A-series engines.
Gasket fitment. Writing side up.
Genuine Mini Spares engine front plate for pre A+ plus timing gear.
this fits engines using the early egg shaped cover
This plate has been modified by counter sinking the 2 main cap bolt holes to accept countersu...
Replace with new camshaft,it's almost too easy to overlook during a rebuild. Camshaft bearings are pressed into the block and thus are usually done by a machine shop. You would not rebuild an engine without replacing the rod bearings, so why not the ...
Steel ring set,for 4 ring pistons. 3 compression rings @ 0.0625" oil rings 0.125 as per original 998 pre A plus and 1098cc versions inc morris minor and sprite range.
Timing cover front plate and tensioner plate bolt and washer kit. Comes with all parts to fit the cover except for the counter sunk screws if fitting a duplex kit (our duplex kits all come with these).
11/16" dowty seal for post 1991 cars where the original pipe has been replaced with a braided pipe or an oil cooler has been fitted using part number MOC4. used on the TCZ102
This is the large seal for the early type oil filter assembly pre spin on type.
Genuine Bosch lambda sensor, fitted to both the twin and single point injection cars and fitted in the same exhaust manifold shared by both cars. Be warned the cheaper non branded sensors cause lots of issues hence we only sell the Bosch version.
Fitting kit comprising of studs, nuts, plain washers, spring washers and a gasket
This kit of head studs is the best available for road and lightly tuned engines. See the C-AHT280 set for highly tuned engines.
The material spec is alloy steel heat treated to 75 tensile tons per square foot minimum and finish...
You should replace the camshaft bearings every time the block goes to the machine shop. These bearings fit all late model 1275cc blocks (the ones without tappet covers on the back) It's almost too simple and thus often overlooked during a rebuild. Ca...
ARP Head stud kit that compromises of;
4 x Long Head Studs
7 x Short Head Studs (Disregard 2 if you're using a 9 stud application)
11 x Multipoint ARP nuts
11 x Heavy Duty Washers
4 x Rocker post studs <...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.