CRANK THRUST WASHER SET 998 3 THOU OVERSIZE
ACL2122-003

£17.22 exc vat

£20.66 inc vat

In stockIn stock
Crankshaft washers for crankshaft at 3 thou oversize on each one

sold as a set of four for 998 and 1100cc.

£17.22 exc vat

£20.66 inc vat

In stockIn stock

Recommended usage 1 x ACL2122-003 to fit one mini.

People also bought products
WASHER FOR ENGINE OIL PRIMING PLUG
6K464

WASHER FOR THE OIL PRIMING HOLE PLUG WHEN APPLICABLE 850/997/998 and also on earlier type oil pressure switch or oil pressure union CAM6431.

£0.60 exc vat

£0.72 inc vat
ENGINE TO GEARBOX NUT AND BOLT KIT
MSSK060

Complete nut, bolt and washer set for engine to gearbox only

£3.50 exc vat

£4.20 inc vat
WASHER FOR BLOCK DRAIN PLUG (53K2853)
6K638

Washer for the drain plug on the rear of the block (53K2853)

£0.53 exc vat

£0.64 inc vat
CRANKSHAFT WOODRUFF KEY
6K836

Woodruff key for the end of the crankshaft to locate the lower timing chain gear and WKN505 is for the camshaft key to hold the larger timing gear.

£4.98 exc vat

£5.98 inc vat
SLEEVE FOR LOWER ENGINE STEADY ROD
31G1085

The metal sleeve 3/8" internal diameter used on the gearbox lower arm stabiliser rod when fitted. Also in our MSSK and MSSK001.

Sold singly

£1.75 exc vat

£2.10 inc vat
HEAD STUD BLOCK TO HEAD SHORT 4" UNC 3/8"
CAM151

You require 5 of these high tensile short head studs and they torque to 42lb/ft. See also complete kit which includes these top grade studs C-AHT279. 3/8"unc stud with unf end for head nut and is 4" long. See other long head stud [link]C...

£4.28 exc vat

£5.14 inc vat
CAMSHAFT GEAR LOCKTAB
2A759

If you are replacing your timing chain or just doing routine maintenance a new locktab is sure to come in handy.

£0.52 exc vat

£0.62 inc vat
PISTON RING SET 998 A PLUS+20
R33636-20

3 OF 0.625 COMPRESSION RINGS AND .1575 OIL CONTROL RING.for P20773 pistons

£61.20 exc vat

£73.44 inc vat
DISTRIBUTOR CLAMP FOR A PLUS DIZZY 85 ON
TAM1671

Prong type clamp that bolts to the block and retains the A plus distributor in place. The screw is TAM1706.

Pre A plus clamp is 501134

£6.00 exc vat

£7.20 inc vat
CRANKSHAFT TIMING GEAR SHIM
6K628

Very important shim to go behind crankshaft timing gear to align both wheels up and get correct alignment/true running of timing chain. Approx 5 thou thick, fit as many shims as required.

£0.51 exc vat

£0.61 inc vat
ROCKER COVER GASKET SILICONE 9 STUD HEAD
GUG705009EVO

Upgraded rocker cover gasket made in silicon, ideal for race cars etc where the rocker cover is removed on a regular basis. Mini Spares fitted one on their 1380cc engine road car in August 2014 with great results. Rarely you may require longer rocker...

£8.20 exc vat

£9.84 inc vat
STABILISER BUSH ONE PIECE PERFORMANCE USE STD FROM...
KKF101320EVO

The last Rover update on the upper engine stabiliser bar, but this is upgraded for performance use.

A one piece silent block type bush, it was fitted at both ends from 1996 on and will fit any cars that had 2 bushes fitted at either end as o...

£3.60 exc vat

£4.32 inc vat
THERMOSTAT HOUSING GASKET LATEST TYPE
GUG705558GM

Genuine version of the thermostat gasket for all A series. Black one side and red the other they are fitted black side to the head. Green to the thermostat.

We have no evidence as yet that they last longer but do look good.

See [lin...

£1.14 exc vat

£1.37 inc vat
RUBBER ENGINE STABILISER BUSH (SINGLE)
CRC5329

These are sold per bush but fitted in pairs.

Apart from very early cars all minis up to 1996 had 2 of these each end.

From 1996 rover fitted a single silent block type bush which will fit your existing 21A1109 arm (par...

£0.78 exc vat

£0.94 inc vat
STABILISER BUSH POLYURETHANE ENGINE KIT
C-STR630

A "must have" for every car. All the torque action of the motor is controlled by the stabilizer arm located just above the flywheel housing. If you are still using original type rubber bushes you are living in the past. Our uprated kit includes four ...

£14.37 exc vat

£17.24 inc vat
OIL FILTER HOUSING - PRE 1992
TAM2097

Filter housing for spin-on filter.

This housing uses a 1/4 npt taper thread union.

The later type (92onwards) 12A engine numbers has 11/16" thread size.

For performance use see 12A2032RACE.

£12.48 exc vat

£14.98 inc vat