£6.00 exc vat
£7.20 inc vat
In stock
£6.00 exc vat
£7.20 inc vat
In stockRecommended usage 1 x PQM100120 to fit one mini.
The original adjuster bolt is very expensive, this kit has been made in stainless steel for longevity and includes all 3 parts for adjusting the fanbelt tension on mpi cars at a fraction of the price of the OEM setup.
Gasket/seal for all 1997 on mpi headlamp bowls (self levelling type).
This is the bracket that bolts to the front of the mpi blocks to hold the more modern type coil pack. The original type is no longer available so we had this made in stainless steel.
Screw for holding PRC1230A to the number plate light body, 1970 onwards.
This is the plug that fits on the back of the front indicator lamps (XBD100670) on mpi models.
Auxilary wiring for genuine Rover spot and fog lamps needed when fitting genuine lamps to cars not originally fitted with auxilary lamps or for cars that have had the wiring damaged. This loom is supplied with complete lamps XBN10008 and...
THE LENS FIXING SCREWS FOR THE REAR LENS ON MK4 1976 ON WITH REVERSE LENS ARE ALL THE SAME. SOLD INDIVIDUALLY. ALSO FITS TWIN POINT FRONT INDICATOR LAMP.
3 per lamp required or 6 per car set.
The best chrome type available with screw and washer.
A headlight trim ring is only the starting point of a good looking car, but you have to start somewhere. Sold singly 2 required per car. These are the original type chrome over solid bras...
Rear fog lamp switch with the orange illumination segment for all vehicles fitted with production fog lamps as standard. 3.1cm tall from 1976 on.
Headlamp bulb found in many of the post sealed beam unit cars. An upgrade is available as GLB472X.Sold individually
Almost any screw will hold the chrome headlamp bezel on, but only one is correct! These screws are stainless steel and will never corrode plus they have the little rubber washer on the backside so that the screw will not fall out when trying to fit ...
These are for Left had drive L/H/D. See S4698B for Right hand drive R/H/D.
Even at normal highway speeds it is common to "outdrive" conventional headlamps. These halogen headlamps have very bright 55/60 watt bulbs. Their special...
Manifold absolute pressure sensor. MAP sensor
converts pressure variations in the inlet manifold and feeds ECU with information--This part also has the part number on a white sticker for easy identification--THE WHITE PLASTIC SOCKET LOOM CAP...
Two of these plastic lens that hold festoon bulbs (GLB239) are mounted in the metal cast number plate housing (13H6900) on all MK3 bootlids from 1970on. Sold individually with bulb LESS FIXING SCREWS.
See PMZ206 for screw replac...
All Minis require an earth strap from the engine to the body and from 1959-1996
they fitted from the gearbox to the subframe. When they introduced the twin point in 1996 it was moved to the upper engine stabiliser arm. About 13"LONG.
Black wiper arm for L/H/D with a hook type fitting introduced in 1990 --This uses an 11" blade GWB911 made by Bosch which is the best blade we have found. 2 per car required and sold singly. Will fit any cars from 1970 on
with ...
Key blank for steering locks. These will only fit our newly made BHM7107 locks.
Fuse Box-Pre 1976
Early style twin fuse box as used on many cars and models. If your box is corroded, as most are, then the "Price of Darkness" is bound to strike you.
This is the 'later' early model with blade connectors and comes...
This front turn lamp assembly was used on all Mkl & Mkll Saloons, all Vans and Pick-Ups. It is also an easy installation on later cars seeking that proper sixties look. Includes amber glass lens, chrome surround and rubber boot. The clips to hold thi...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.