£150.00 exc vat
£180.00 inc vat
In stock
converts pressure variations in the inlet manifold and feeds ECU with information--This part also has the part number on a white sticker for easy identification--THE WHITE PLASTIC SOCKET LOOM CAP...
£150.00 exc vat
£180.00 inc vat
In stockRecommended usage 1 x MHK100600 to fit one mini.
Genuine Bosch lambda sensor, fitted to both the twin and single point injection cars and fitted in the same exhaust manifold shared by both cars. Be warned the cheaper non branded sensors cause lots of issues hence we only sell the Bosch version.
Also known as the idle air control valve (IACV). Bolts on the side of the injection body housing to control engine idle speed and air flow from cold start up. The blue socket loom cap fits this unit. This is part of MLZ100090. After fitt...
Lots of things have been written about performance plug ignition wires but regardless of what you believe we all know that good wires are a must. This special competiton wires set from the Lucas factory has 8mm wire and the highest performance, no br...
Bolts on the side of the injection body housing to control engine idle speed and air flow from cold start up. The blue socket loom cap fits this unit. This is part of MLZ100090. After fitting the cars ignition needs to be turned on and o...
Set of 4 ignition leads from the original supplier to Unipart, suitbale for all twin point minis 1997 onwards
Genuine Mini Spares product. The seal that goes on the neck of petrol tanks as protection against water intrusion and to also to make the hole look neater, so replace them when they crack or shrink through heat. This is the original fatter type as us...
Gasket/seal for all 1997 on mpi headlamp bowls (self levelling type).
RESIN BASED CONDENSER as per the original Lucas type made for the 23/25D type distributor as fitted to original Cooper S or Racers who want a trusty part or where originality is required,with soldered wire connections and correctly made foot to sit ...
Screw for holding PRC1230A to the number plate light body, 1970 onwards.
Stainless steel screw kit for all mk2/3 lens to lamp body. Comes as a car set with six screws and six fibre washers.
This is a dummy control box (GEU6603) for use with the Dynalite alternators, enabling you to keep your engine bay/wiring looking original even when you are using an alternator. All wire can be swapped like for like from your old regulator box except ...
Best on the market, sports coil-Not Lucas. A standard coil can only do so much, and when compression is raised (as in most high performance engines) or improper fuel mixtures occur something better is needed. This sports gold coil with proven origina...
Basic idle air control valve for spi Mini's. Unlike the mpi stepper motor which uses a bypass valve this unit controls the throttle directly, if you are having issues on idle then 1 or more of the 4 windings could not be working, this is usually due ...
Maxi fuse located in the engine bay fusebox on all post 1997 mpi cars, 30amp.
The main cause of failure is water in the pump. This is caused by modern ethanol fuels. Be sure to clean the tank out before fitting and drive your mini more to avoid water build up.
Replacement pump only for the original WFX100810<...
5/16" bore petrol hose for injection cars sold in metre lengths.
Resilient to heat,weather and suitable for ethanol in modern day fuels.100psi max.R9 spec.
These are the screws needed to fix the condensor, points, base plate and vacuum to 45D and 59D distributors. For 23/25D type see 17H5106
These are the screws needed to fix the condenser, points and base plate to 23/25D distributors. See 57H5135 for 45D type distributors.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.