MPi REPLACEMENT FUEL PUMP ONLY
WFX100812

£48.51 exc vat

£58.21 inc vat

In stockIn stock
The main cause of failure is water in the pump. This is caused by modern ethanol fuels. Be sure to clean the tank out before fitting and drive your mini more to avoid water build up.

Replacement pump only for the original WFX100810 pump (doesn't come with tank fittings).

Requires a small amount of wiring and pipe modification to fit, but half the cost of the

original unit. Small terminal is EARTH/ground.

£48.51 exc vat

£58.21 inc vat

In stockIn stock

Recommended usage 1 x WFX100812 to fit one mini.
Fuel Tanks and Pumps - Qty 1

Recommended products

Gasket/seal for mounting the fuel pump to tank for SPI and MPI Mini's

People also bought products

The main cause of failure is water in the pump. This is caused by modern ethanol fuels. Be sure to clean the tank before fitting and drive your mini more to avoid water build up.

Replacement pump only for the WFX100810 (doesn't...

Mini Spares Non Genuine version mechanical fuel pump. Brilliant aftermarket alternative for cars pre 1990.

Drives off the camshaft at the rear of the motor. These pumps are generally reliable but when a diaphragm goes bad it can be very bad ...

Non Genuine metal bodied electric fuel pump with metal banjo pipe ends for long life,with blue plastic end. Ethanol tolerant and resistant internals.

This is a cheaper alternatives for the original SU pumps, different to look at and fit but ...

THE ELECTRICAL CIRCUIT FOR THE FUEL PUMP INCORPERATES AN INERTIA FUEL SHUT OFF(ifs) SWITH WHICH WILL STOP FUEL BEING DELIVERED TO THE ENGINE IN THE EVENT OF SUDDEN DECELERATION--It is fitted in the engine compartment, fixed to the bonnet switch brack...

Gasket/seal for mounting the fuel pump to tank for SPI and MPI Mini's

Fuel pipe from the fuel filter to engine on spi and mpi models up to chassis no WD169574 when fuel filter GFE7059is fitted.



Tube nut has four threads, the metal pipe has a union on the end that is fatter than the metal...

Made for the facet solid state range of pumps (SS501/SS502/SS503) this pre filter with screw in union must be used to eliminate fuel tank debris damaging either the filter or carb/engine etc.

Special rubber hose 1/4" bore for use on petrol lines, this is in black and not armour plated outside but does have internal reinforcing. Supplied as pre cut 1m length with 2 clips and is safe to use with modern fuels with higher ethanol content. SAE...

This solid state electrics kit fits your standard pump to eradicate those old stcky points system that let down an otherwise good pump. these fit the AUF214

original electric fuel pump. for positive earth see EPK12P

Used on Facet range of solid state and silver fuel pumps SS501/2/3 with 1/8" nptf thread size with 1/4" standard fuel line.

named after its shape thesre are 2 of these on plastic outlet covers on every SU electric pump and the gasket underneath them is AUB676

Only used for STC505 Facet pump range or solid state SS502 & SS503 and silver fuel pumps with 1/8" nptf thread size with 5/16" upgraded fuel line.

Before the days of Aeroquip, Minis were fitted with braided steel rubber fuel lines. They should be used in place of rubber for all fuel lines in the engine compartment. They come made to length, with rubber end caps. 1/4" bore size.

Orange ...

If you have a mechanical fuel pump fitted to your engine this spacer block fits between it and the engine. The gaskets are available seperately however as GUG705779GM.

Paper gasket for either side of the spacer on all mechanical fuel pumps fitted on the rear of engines. The spacer with gaskets fitted is available as GUG705603GM.

A genuine original S.U. pump ETHANOL tolerant since 2011/2 that will fit into your original mountings with no hassle. Suitable for all cars with electric "pusher" pumps. Replacement points for this are available as AUB6106A.

An...

this rubber mounting kit helps to dampen the pump ticking noise as well as acting as an earth

Ideal well priced electric fuel pump for replacing either electric or mechanical pumps when using single HS or HS2 twin carbs 4.00-5.5 PSI delivering 18 gallons per hour.

Other parts required to fit this pump are:

FPA9...

Fuel pump with filter for injection models where the pump is located inside the tank. This pump was originally for the twin point but is now used on both Single or Twin point injection models as the ECU adjusts the pressure on demand.

See [l...

Solid state competition fuel pump with 6-00-7.252PSI 25 GALLONS PER HOUR.

Uses FPA 903 union or FP903A if you wish to upgrade fuel line size for extra flow theses are ideal for single HS4/6 or twin SU carbs.Next step up in pump is [link]STS5...