£1.80 exc vat
£2.16 inc vat
In stock
Overall length is 48mm
Sleeve length is 32mm
Sleeve diameter is 13.8mm
The washer is 2.3mm thick and outside diameter is 24mm
£1.80 exc vat
£2.16 inc vat
In stockRecommended usage 16 x REV09C to fit one mini.
The original British made design Revolution wheel not to be confused with Revolite . ET03 offset.
No longer engraved with the word Revolution
The original British design Revolution wheel not to be confused with the Revolite copies. ET05 offset. Supplied with chrome plated wheel nuts and centre caps (spare caps are part number REV06).
Our aluminium 4 pot and S c...
Solid version of NAM9075 chrome plated without the troublesome stainless steel cover that gets destroyed by wheel sockets. This uses 17mm socket.
Stainless steel wheel nut for our 10" rose petal alloy wheels, this is the longer version needed when using the wheels with the spacer, includes stainless steel washer. 32mm long.
these will fit MB split rims
Stainless steel wheel nut for our 10" rose petal alloy wheels, this is the shorter version needed when using the wheels without a spacer, includes stainless steel washer. 25MM long.
The original stock nut has a very small area of contact to absorb all the loads of cornering, etc. Our special "wide seat" nuts almost double the contact area! The first designs (Bugeye) use a flatter seat than the more common "Rostyle" type. Chrome ...
Stainless steel sleeve nut with tapered washer.
5/8" SHANK DIAMETER and 16mm long shaft. Sold individually as fitted to our Special Tuning wheel range where applicable.
The best reason for buying our wheels is that spare ...
The original mini wheel nut with a round seating was fitted from 1959 until 1984 when they changed to a 60 Degree straight seating wall. This later nut was 113087. 10" wheels with plastic hub caps used a strange looking nut to hold the c...
Wheel bolt for Minilites.
The Minilite company has gone through some very difficult times over the last number of years and all the changes of ownership have caused severe supply problems. These are 15.75mm wide 38mm long shank with overa...
Over the years Minilite wheels have been made in different widths and offsets, they all took .625"(15.7mm) diameter lug nuts, but the lengths vary. They are sold "each". This one has a shank length of 19mm long and will only fit the 5x10 minilite. T...
Wheel nut for the mini 20th birthday special edition with 10" wheels. Shank length is 8.5mm, shank diameter 15mm.
The Minilite company has gone through some very difficult times over the last number of years and all the changes of ownership have caused severe supply problems.
Lug nuts. 15.75mm wide shank 21.5mm long shank length and overall length of...
Minispares own stainless steel wheel nut and zinc plated washer for some Mamba and Revolution wheels except 13".
Shank length under the flat washer is 28mm. Shank diameter is 13.9mm.
Wheel Nut for Genuine Rover Cooper 8 spoke and MPI Sportspack wheel. Price is for one wheel nut not a set as pictured. You must use a 6 sided 11/16" socket and not a multi sided socket to avoid damaging the wheel nut. Original nuts from the factory u...
If your wheels are using a tapered seat style wheel nut you must consider this latest safety option! The original stock nut has a very small area of contact to absorb all the loads of cornering, etc. Our special "wide seat" nuts almost double the con...
These chrome wheel nuts have the 60 degree fitting angle on them which was introduced as standard on original production car wheels from 1984 on.
When the 12" steel wheel was introduced as standard in 1984 they changed the wheel nut seating angle to 60 degrees.
Chrome Lug nut.
Fit stock 10" & 12" wheels. Also fits Minator and other Mag wheels that take a radius seat type nut.
Plain spun ally centre cap for the original 10" steel wella wheel. 63mm rear fitting cap, 45MM DEEP with logo face of 45mm.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.