£90.00 exc vat
£108.00 inc vat
Out of stock
RACE quality bearing set being made at the Mahle Motorsport Race Bearing Division Vandervell F1 plant in ...
£90.00 exc vat
£108.00 inc vat
Out of stock
These con rod bolt and nut set are made by ARP in the USA and considered the best available FITS 1300 con rods plus MGB late 18V engine numbers with 11-32" bolts. Quantity required one kit per car. torque up to 38-40lb ft.
Genuine part on sale at less than half price.
Most engine builders will tell you to replace the rod bolts as often as you can afford, but at least every other time you do the bottom end. If you don't know the last time, replace them. The [li...
Multi point big end journal nut for 1.75" bearing size con rods. These are multipoint nuts as fitted to Pre A plus engines. A Plus engines used CAM6263 which had the built in flange to spread the load but are not available. They are in...
Mahle was Vandervell bearings 1.064" 27.05mm wide mains for the late 850cc plus all 997/998/1100cc at standard size. Early 850 mains were VP592 and 1.185" 30.10mm wide..Quantity required-1 set.
Rod bearings, 850-1275 1 5/8" journals. Heavy duty steel backed bearing for durability and long life. Vandervell, once the only bearings to use on a competition motor they are now made by Mahle. ACL is now commonly used in race engines.
Replace with new camshaft,it's almost too easy to overlook during a rebuild. Camshaft bearings are pressed into the block and thus are usually done by a machine shop. You would not rebuild an engine without replacing the rod bearings, so why not the ...
Standard size crankshaft washers as a set of four, fits 998 and 1100cc.
ACL Main bearings for the crankshaft as preferred by performance engine builders standard size
Sintered copper lead, lead plated,steel backed
Nominal Composition
Copper 74%
Lead 24%
Tin 2%
Rod bearings, 850-1275 1 5/8" journals. Heavy duty steel backed bearing for durability and long life. The bearings to use if you want it to last. The only bearings to use on a fast road car.
( Tri-Metal )
Sintered copper lead, lead...
Race quality heavy duty double row performance endless timing chain. It is the best chain available and used by top engine builders, also fits MGB/Midget. This chain is for duplex gears that is used by racers as a limited stretch heavy duty version m...
998cc flat top 3 ring circlip type piston set as fitted to early A plus to replace 4 ring set type. Gave 10.3 to 1 CR and is a good alternative to use on any 998 with circlip type pistons. Replaced 4 ring (3 ring and scraper) P20754 from Hepolite 198...
Lower Stabilizer Kit, RH.
Designed as an almost mandatory addition to any Mini with a rod change transmission, extra stabilizers will greatly aid any car. In stock form the control is left to the upper stabilizer. This often results in not o...
Woodruff key for the end of the crankshaft to locate the lower timing chain gear and WKN505 is for the camshaft key to hold the larger timing gear.
Mini Spares Non genuine timing chain gasket fitted to every BMC A series engine with 10 gasket holes until the introduction of the A plus type which had a bulge in its side where the tensioner was fitted which had 11 holes.
Gasket material h...
Converted into a non melting type grease.Favoured by proffessionals for camshaft,lobes and lifter,and any valvetrain to stop scuffing on start up. Also useful for oil pumps to stop drain back on start up
For race quality chain see 2H4905EVO.
It only makes sense that if you have your engine out of the car that you replace the timing chain. The chain controls the timing of the camshaft and even a slight amount of wear or stretch c...
Original short pin drive oil pump for all Pre A Plus minis with 850/998/1100cc engines except autos and others with star drive or the later slot drive pumps as found on A Plus blocks.
Made in EN24T for strength they have been made to fit the majority of flywheels that seemed to slightly differ from the mid 60s. Run a file down the raised keyway if tight. This flywheel locking plate is for pre verto diaphragm clutches. For Verto ty...
If you are replacing your timing chain or just doing routine maintenance a new locktab is sure to come in handy.
Slot drive pump for 998cc A-Plus engines.
All oil pumps are not created equal! Almost all pumps available today have the same design capacity. The problem is the lack of precise manufacturing. Most factories in their quest for production vol...
Mini Spares own Universal gasket set.
This engine block gasket set fits all manual blocks and include rubber tappet chest covers and bolt seals, also including A plus and Pre A Plus timing gear and cover gaskets. For the equivalent gasket se...
Paper gasket for either side of the spacer on all mechanical fuel pumps fitted on the rear of engines. The spacer with gaskets fitted is available as GUG705603GM.
Keyed or cupped, either variety does the job. A plus engines use a TAM2020.
Countersunk screw for holding the front palte to the crankshaft bearing cap on cars fitted with duplex gears to give the clearance required. 2 required per car.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.