ALTERNATOR BRACKET (LOWER) TWIN POINT ONLY
YLU102340

£54.00 exc vat

£64.80 inc vat

In stockIn stock
Bracket for bottom of alternator on all twin point injection cars which also held air compressor on Japan and some German cars that had air con as standard.

Also help to mount the fan belt tensioner wheel. Casting number on this item is YLU1...

£54.00 exc vat

£64.80 inc vat

In stockIn stock

Recommended usage 1 x YLU102340 to fit one mini.
Alternators and Starter - Qty 1

Recommended products

THE M10 METRIC bolt 25mm long for holding alternator plus other parts on the Twin point minis

People also bought products

The original adjuster bolt is very expensive, this kit has been made in stainless steel for longevity and includes all 3 parts for adjusting the fanbelt tension on mpi cars at a fraction of the price of the OEM setup.

Special bolt that fits the engine front plate to support the adjusting link for alternators/dynamo

Alternator bracket for A Plus engines and Pre A+ engines with dynamo fitted. See 12G1053 for earlier Pre A plus alternator bracket.

Fitted from 1996 only this alternator sits higher than originally, with new brackets that will only fit the twin point injection cyl head. A1151-65 type producing 65amps (Was GXE2862 from Unipart). If your battery seems to be always running low it mi...

New lenses do a lot to improve the looks of a car, and may make it more visible. To make sure that they match we recommend that you replace both lenses together.

Original equipment on the twin point cars this is the roof mounting base and the ariel comes seperate-See XUJ100070

Metal plate switch carrier for 5 square type switches.

Universal post type battery earth strap with clamp type fitting and correct length for most alternatives of batteries fitted.

Genuine R/H metal based lamp assembly,this is the only quality part made in UK from original tooling unlike others available from our competitors.

The assembly includes an amber/red lens and the body rubber seal. Fits the right rear of your...

Genuine L/H metal based lamp assembly,this is the only quality part made in UK from original tooling unlike others available from our competitors.

The assembly includes an amber/red lens and the body rubber seal. Fits the left rear of ...

This lamp unit comes without a bracket and will fit either side, if your bracket is okay. The unit only comes from Rover with bracket but costs £29-93 so we supply it less a bracket at £10-00 savings. If you require a bracket for the right hand it is...

This is the detachable mast part of the roof arial on the twin point cars.

The base unit is XUF000020.



this is the factory standard long aerial, not a short one



measures @ 78cm

Upper amber and red (indicator and stop) lens left hand for Lucas rear lamps with a built in reverse lamp. Will not fit altissimo which had a one pice complete lens, see AAU4946/7.

You can scrub all you want on those old plastic tail light lens and they will never look as good as new ones. If yours is cracked or beaten then it should be a no brainer, replace them and look sharp.

this lamp was fitted into the headlining at the end of 1984 and replaced the earlier type lamp EAM1650---(bulb not included) GLB245 but GLB207 is a 5 watt alternative that many cutomers use.

Also fitted to some Land...

Also known as crankshaft position (ckp)sensor for single and twin point cars.



can use 2 x SC105120 bolts to attach it M5 x 12mm

This is the lower left hand clear lens with a small red reflector fitted to all Lucas type lamps on saloon cars from 1976 on which also had the reverse light incorperated into it.

This is the lower right hand clear lens with a small red reflector fitted to all Lucas type lamps on saloon cars from 1976 on which also had rhe reverse light incorperated in it. But as they are so big they also seems to be hit first! If you have c...