EXTERNAL DOOR HINGE L/H TOP MK1/2
14A6819

($30.39) £30.39 exc vat

($36.47) £36.47 inc vat

In stockIn stock
Hinge for any mini with external hinges and uses gaskets BMP135 on A panel and and ALA7844 on door. Supplied with new studs/nuts and washers for fitment but if you need spares see 14A6818BOLT. A hinge and bolt and bush repair kit is also available for these hinges -see MS15

New set of bolts and washers--the studs have allen socket ends to help put them in easily without damage, hence the price

($30.39) £30.39 exc vat

($36.47) £36.47 inc vat

In stockIn stock

Recommended usage 1 x 14A6819 to fit one mini.
Front Door - Sliding window type - Qty 1

Recommended products

THIS IS THE SMALL DOOR HINGE GASKET ON THE A PANEL FOR SLIDING WINDOW TYPE DOORS.

THIS IS THE LARGE GASKET THAT FITS BEHIND THE HINGE ON THE DOOR OF AN EXTERNAL

HINGE ON CARS WITH SLIDING WINDOWS SUCH AS MK1/2. SEE BMP135 FOR SMALL ONE.

Angled spacer washer for Mk1/2 external door hinge cars for the upper hinge

Alternative products

Perhaps one of the most endearing features of the early Minis with sliding windows are the external door hinges, that is until they are worn beyond repair and sag to the point that the door won't close. Replacements are available individually, but th...

This kit contains one pin and one bush for repairing the external hinges on MK1/2 doors. If they are badly worn and you need Hinges see 14A6818/19/20/21.

If you require a new set of studs see 14A6818BOLT a complete car set in st...

People also bought products

Upper door moulding rivet for Cooper S door trim. For Mk1 usually 1 at front and 3 at back making 4 per side and on Mk2 there were 2 per end at bottom making 4 per side. This is the 10mm head rivet and not required on our own 14A9773/9774 trims that ...

Complete fitting kit for the door check straps on all Minis fitted with external hinges.

Angled spacer washer for Mk1/2 external door hinge cars for the upper hinge

Door hinge shim for all wind up window cars, these are used to align the doors, 0.7mm thick and made in stainless steel, use with ALA6382 to get good door alignment. See ALA6381 for thicker rear support plate.

MK3 door hinge fitting kit for all internal hinged doors. (hinges not included)

Door hinge shim for all wind up window cars, these are used to align the doors, 1.2mm thick and made in stainless steel use, with ALA6383 to get good door alignment See ALA6381 for thicker rear support plate.

SPECIAL 6/32" UNC COUNTERSUNK POZI SCREW 1/4" LONG FOR HOLDING THE 14A6835 BUFFER PLATE TO BODY.

This screw can used to hold together the 2 halves of the disc shields on all

mini front discs. fits MK1/2 door escutcheons.

Use SE910161 and cut down to 3/8" long including head

PMZ306 was originally 3/8"long u...

Full Mk2 door handle set with 2 front door locking handles and boot handle with matching keys. Fitted from 1966 with the intoduction of the door safety escutcheon boss. This boss is available as 24A1834 and gasket 24A1835.

Regre...

A great accessory for wind up window minis. Fitted in minutes to make such a difference driving your Mini with the window open. Wonderfull for those that smoke or love fresh air. In a tinted colour to stop bad reflections.

New set of metric studs, bolts, nuts and washers as supplied with the alloy external hinge kit (PEASE NOTE: This kit is NOT suitable for the original hinges). The studs have allen key socket ends to help put them into the hinge easily without damage,...

4 Non Genuine door hinges as a car set for wind up window type doors from 1970 on. These are a top quality item as opposed to the cheaper junk version available on the market.

Sold seperately as

top right CZH202MS 1 r...

Lower internal door hinge for either side.

Fits all wind up window type doors from 1970 on.

upper door hinge l/h for wind up window type door with internal hinge 1970on

this is not a genuine part and is available in a car set kit MSSK017B

See CZH203 for genuine

Multi purpose square plastic plug/nut for No8 screw size was used on many door fixings and fuse box to body.



Also suitable for Twin Point indicator fixings.

Sliding window type weatherstrip kit R/H

kit contains lower and upper sliding channels plus the vertical strip that attaches to the glass as a draught excluder plus the stainless steel window catch runner that the lower channel sits in,with ...

Sponge type seal on L/H A post of all minis with wind up window type doors to protect from water running down into body. A part you must keep your eye on to stop rust.

Sponge type seal on R/H A post of all minis with wind up window type doors to protect from water running down into body. A part you must keep your eye on to stop rust, if the sponge is gettig hard then replace it.

Moulded shape type right hand door stay grommet fitted until 1985 when it was replaced by a flat sponge type seal CGE10038/9.

Genuine MK3 wind-up window upper slide up and down felt lined channel that fits into the R/H upper door frame. Left (PAM3077) and right (PAM3076) look identical but are mirror images.