($5.03) £5.03 exc vat
($6.04) £6.04 inc vat
In stock
Genuine AP Lockheed rubber boot
($5.03) £5.03 exc vat
($6.04) £6.04 inc vat
In stockRecommended usage 2 x 17H7612GENUINE to fit one mini.
Rubber gaiter to keep debris from entering the drum via the backplate handbrake lever SMN10005. Sold singly per backplate, 2 required per car.
For mk1/2/3 Van,Pickup,Estate upto 1976 which had 2 cables from the lever.
FOR SALOON MODELS USE GVC2022
If your car has 2 cables running from the lever as per pre 1976 cars for dry suspension only but NOT VAN,PICKUP and ESTATE
Hanbrake cable for hydrolastic cars which used 2 of these and are different from dry suspension cars . SEE GVC2022 for dry pre 1976.
From 1976 the handbrake cable layout was changed --instead of two cable from the handbrake it was changed to one. Front for the saloons is GVC2135 at 25" long and the van requires a 29.5" long cable which this one is. The cable between ...
Concave washer for the CLZ549 pin on the quadrant of dry suspension minis.
Pretty alloy handbrake quadrants for those special cars, with an extra 6 cut out holes giving extra lightness. Dry suspension cars pre 1976 only.
Supplied as a pair.
Kit contains a new pawl and two new rivets, with fitting instructions.
By simply replacing one component of the handbrake lever you can change to "fly-off" operation. This means that you'll have to push the button to lock the lever, otherwi...
This is a pair of rear brake back plate actuating levers. One Left and One right hand. If you want the rubber gaiters they sit through, order individually as 17H7612
Non spacered die cast alloy brake drums. The alloy material has a finned design that dissipates heat quicker which in turn helps reduce brake fade. Sold as a pair of drums.
This bracket is the main mounting bracket for the handbrake lever assembly and is welded onto the back of the seat crossmember and to the rear floor section.
Only for Pre rod change cars with twin cable handbrake.
The later type bra...
This bracket is the main mounting bracket for the handbrake lever assembly and is welded onto the back of the seat crossmember and to the rear floor section.
Only for rod change cars with late type single cable handbrake.
the early ...
special shaped nut for handbrake cable at handbrake end
Twin cable use 2A5858
The rubber type grip fitted on handbrakes-
will fit any single cable hand brake from 1976 on
Mk1/2 used 13H5541 thinner plastic type--to fit this to pre 1976 early cars you will need to put lots of sticky tape on the h...
Die cast alloy brake drums with built in spacer-imported copy but have proven 100% reliable on sales from 1998 without any problems. The alloy material has a finned design that dissipates heat quicker which in turn helps reduce brake fade. While desi...
All MK3 minis to 1978 except Cooper S MK3 which used 21A1774.
Fitted mainly to cars with 3/4" larger bore rear wheel cylinders.
The correct regulator valve for all MK1/2 mini plus all Cooper S inc MK3 is 21A1774 where m...
Genuine AP brand new rear Left Hand back plate assembly (beware of copies).
These are ready to bolt on, brand new stock from AP Automotive and have the .75" bore genuine wheel cylinders GWC1102. Remember that all wheel cylinder ...
Genuine AP brand new rear right hand back plate kit (beware of copies).
These are ready to bolt on brand new stock from AP Automotive and have the .75" bore genuine wheel cylinders GWC1102. Remember that all wheel cylinder rubb...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.