($121.70) £121.70 exc vat
($146.04) £146.04 inc vat
In stock
($121.70) £121.70 exc vat
($146.04) £146.04 inc vat
In stockRecommended usage 1 x C-AEG371 to fit one mini.
Metal gasket for the catalyst and is the same both ends for Cooper 1275CC RSP early cars, but only fitted on the front to later cars. If you cannot fit this gasket on the rear your car does not need one.
Special tin plate type of gasket that goes between the manifold and exhaust downpipes on all injection cars.
The original replacement is expensive so when it needs replacing many customers
opt for our stage one kit C-STN22 which gives extra power for litle more cost.
in this kit you will get an exhaust manifold, which is bette...
Standard bore LCB (inch and three quarters internal diameter) for post 1990 cars with catalyst that is ideal for for standard to high performance 1275s and for street 1380s. The best quality production manifold is made by Maniflow. The Long Centre B...
if your front downpipe or exhaust needes replacing this conversion will give you extra power for little more. A new better flowing downpipe with a flexible knuckle plus our super RC40 single box rear silencer for that slightly sporty sou...
This is the clamp on the cooper freeflow manifold to clamp it to the engine for extra support, supplied with tag.
Small bore Maniflow LCB. Has a 1.5" outer diameter 1.375" internal diameter bore size. STD mini exhaust and downpipe size is 1.250".
If the 1.375" tapered end of about 2" is removed a 1.750 pipe will fit over remaining length of outlet pipe.
Special reinforced gasket for injection cars has metal inserts on exhaust ports plus a metal back on the manifold side which makes surface easier to clean when replacing. Often used on Turbo cars when correct gasket is in short supply.
...
Exhaust manifold to downpipe clamp.
The key to eliminating exhaust leaks at the manifold flange is the clamp. These new clamps include proper brass nuts and support washers. Fits most 850cc, 948cc, 998 etc. Those engines with single carb an...
For the medium bore Maniflow LCB Y piece or AN180V. 48mm ID
LONG CENTRE BRANCH EXHAUST MANIFOLD FOR FUEL INJECTED CARS WITH A SENSOR TAKE OFF in main LCB body, THIS IS FOR USE WHEN THE CATALYST IS BEING REMOVED AND A RC40 EXHAUST IS BEING FITTED. If the catalyst is to be retained use [link]C-AEG3...
Special tin plate type of gasket that goes between the manifold and exhaust downpipes on all injection cars.
This short pipe fits on the end of our freeflow manifols C-STR816 to give the overall length of an LCB when you have an exhaust system to fit that was made explicitly for LCB fitment.Total length is 300mm ID is 44mm OD is 48mm.
Manifold gasket fitted to all A series pre 1992 except Turbo which had a reinforced exhaust ports GUG704063MG and SPI from 199. From 1991 on a new better gasket with reinforced exhaust ports and backing was fitted GUG704053MG
If you wish to delete the catalyst (legal restrictions apply, so check to see if you are allowed) this pipe is specially made to replace it.
Link pipe for fitting between the LCB and the catalyst. It has a stainless steel knuckle joint to prolong life and give the flexibility required on the system to overcome damage. See also alternative RC40-016
Y piece replacemen...
Special length and thread pattern only for the exhaust manifold to downpipe of injection cars, see also FX108047 special nuts. Metric M8.
The newest development in the A-series engine is the use of these nuts with swedged-on washers. The washer will not separate from the nut, so you won't lose it. Yet the nut rotates independently while you tighten it. What a great idea.
Manifold stud for all A series injection engines and some late carburettor cars which is 45mm long-6mm longer than 53K487.carburettor engines usually retained the 53K487 shorter screw for the outside 2 holes.
Sold singly,6 per c...
1.75" Bore centre exit twin tail pipe maniflow rear box with adaptor to sleeve down to the standard mini 998cc type exhaust system.
1.75" bore twin box, centre exit exhaust system. This exhaust system by Maniflow is straighter and louder than the RC-40. Very high quality with a skid plate on the bottom of the muffler and a polished stainless tip.
Locating rings originally made for 12G295 heads with twin carbs to line up the inlet manifold to the inlet ports on the cylinder head it found its way on most twin carb factory produced cars. There is a recess in the inlet port on the he...
For all cars with a catalyst--this section fits from the catalyst back and has 2 silencer boxes.1.75" bore
Standard bore the rear silencer box has twin upswept chrome DTM style tailpipes.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.