($122.63) £122.63 exc vat
($147.16) £147.16 inc vat
In stock
($122.63) £122.63 exc vat
($147.16) £147.16 inc vat
In stockRecommended usage 1 x C-ARA350 to fit one mini.
SINGLE BOX CAT BACK SYSTEM. TWIN ROLLED END TAILPIPES UPSWEPT. 45MM PIPE SIZE.
1.75" bore single box, centre exit exhaust system. This exhaust system by Maniflow is straighter and louder than our RC40 system. Very high quality with a skid plate on the bottom of the silencer and a polished stainless tip. Suitable for use with an...
1.75" bore twin box, centre exit exhaust system. This exhaust system by Maniflow is straighter and louder than the RC-40. Very high quality with a skid plate on the bottom of the muffler and a polished stainless tip.
this is centre exit 1.8750 bore size exhaust system when no catalyst is required and fits over the standard LCB or in a large bore LCB
For all cars with a catalyst--this section fits from the catalyst back and has 2 silencer boxes.1.75" bore
Standard bore road LCB (1-3/4"id) that has an enlarged and reshaped middle pipe which creates a type of vortex, simulating a pulsing effect similar to the outside two pipes,thus producing an improved BHP,Torque and power curve.Ideal for very hot smal...
Large bore LCB for competition use or on very large bore street engines; such as 1400cc+. Y-piece outlet end is 2" outside diameter, 1.875"id.
The best quality production exhaust manifold available from Minispares. The Long Center Branch...
Standard bore LCB (1-3/4"id) that is ideal for very hot small bore engines, for standard to high performance 1275s and for street 1380s.
There is NOT enough clearance room when fitting to old cars with rubber couplings which foul. Using [lin...
LONG CENTRE BRANCH EXHAUST MANIFOLD FOR FUEL INJECTED CARS WITH A SENSOR TAKE OFF in main LCB body, THIS IS FOR USE WHEN THE CATALYST IS BEING REMOVED AND A RC40 EXHAUST IS BEING FITTED. If the catalyst is to be retained use [link]C-AEG3...
Maniflow's tubular reproduction of the original Cooper 997/998cc exhaust manifold manufactured out of the same tubing as the STD bore LCB. This free flow manifold works vey well at lower speed pick up, the LCB is noisier but better at the top end of ...
Standard bore LCB (inch and three quarters internal diameter) for post 1990 cars with catalyst that is ideal for for standard to high performance 1275s and for street 1380s. The best quality production manifold is made by Maniflow. The Long Centre B...
Downpipes to fit onto the original exhaust manifold when retaining the catalyst on fuel injected late Coopers. Manual cars only
Downpipes to fit onto the original exhaust manifold when deleting the catalyst on fuel injected minis and fitting an RC40 complete system.
Exhaust manifold to downpipe clamp. For 32mm o/d pipe size.
The key to eliminating exhaust leaks at the manifold flange is the clamp. These cast clamps are the best style to use. A real piece of kit to use eradicating a multitude of likely p...
The very rear bobbin type mounting rubber on every mini made until the introduction of a rubber hanger strap in 1992. When the RC40 or similar systems are fitted, 2 will be required. This is a stronger poly version.
Rear RC-40 twin box system to fit catalyst for cars built late 1991 on SPI(not early carb coopers). It has the hanger rods fited for mounting onto the rubber type straps. This makes it a twin box system with a little throatier pleasing note, but a mu...
Blanking plug to blank of the Lambda sensor hole on all SPI/MPI models.
M10 metric flanged bolt 35mm long for catalytic converter. (4 required per unit)
This sleeve will allow an 1"3/4 rear box to fit a standard bore front pipe of a 998cc mini. The large end fits into the RC40 and the smaller end accepts the 1.25" diameter as standard 850/998 exhaust pipe bore
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.