STEERING RACK SPORTSPACK MINI LHD
GSR1185

($80.00) £80.00 exc vat

($96.00) £96.00 inc vat

In stockIn stock
Left hand drive steering rack for all sportspack models, 1997 onwards. The rack has reduced lock in order to help with clearance of the larger 6x13 sportspack wheels.

($80.00) £80.00 exc vat

($96.00) £96.00 inc vat

In stockIn stock

Recommended usage 1 x GSR1185 to fit one mini.
Steering Rack - Qty 1
Steering racks - Qty 1

Recommended products

Mini steering racking fitting kit comprising of 2 U-bolts, 4 nyloc nuts, 2 plastic anti friction stipes, the foam rack to body seal and the half nuts to lock the track rod ends

People also bought products

Mini steering racking fitting kit comprising of 2 U-bolts, 4 nyloc nuts, 2 plastic anti friction stipes, the foam rack to body seal and the half nuts to lock the track rod ends

Nylon bush for original C.A.M steering racks fitted by Leyland/Rover.

Special shaped U bolt for holding the steering rack in place. Every mini uses 2 of these and make sure you fit the 21A2553 plastic anti friction strips. Sold singly

The sponge dust shield that fits over the splined area of the steering rack as it bolts up against the bulk head. Usually it is sold with the centre part cut but not pushed out, but it pops out easily and is shown on our picture as a reference only. ...

Quickracks-If you are interested in performance driving then you know reaction time from the driver to the car is critical; the time it takes to turn the steering wheel to the desired angle is important! The standard rack is 2.7 turns lock to lock, o...

Longer track rod end for running with negative camber, gives an extra 5mm of adjustment approximately over the standard item. Has consistent thread pattern and perfect design to our requirements to fits all known racks and classed as a competition tr...

This is the rubber gaiter that fits suspension knuckles GSV1118, GSV1118MS, Plus it also fits many aftermarket and some old genuine track rod ends. Rover and Unipart changed designs and suppliers many times so we cannot advi...

Called an anti friction strip this plain looking (plastic) piece of strip is used on all mini steering racks between the U bolt and the rack probably because the U bolt is hard steel and the rack is softer rough cast alloy. See 2A6208 fo...

Quickracks-If you are interested in performance driving then you know reaction time from the driver to the car is critical; the time it takes to turn the steering wheel to the desired angle is important! The stock/standard l/h/d steering rack is 2.7 ...

Right hand drive steering rack for all sportspack models, 1997 onwards. The rack has reduced lock in order to help with clearance of the larger 6x13 sportspack wheels. Very useful when fitting aftermarket 13" wheels that foul bodywork.

Brand new rack for Mk2 on Left Hand drive cars less track rod end joints,with no neccessity for old rack in exchange.On most of these racks one of the small bolts that holds the pinion cover on sticks out. do not be tempted to tighten it up as it wil...

Genuine track rod end joint for all factory mini steering racks. If you prefer non genuine see GSJ734MS. If you need more thread on your track rod end as required with non standard camber or lowered cars see C-AJJ1572.Sold i...

these are our last few genuine new steering racks for the old A series engine Metro, less track rod ends at the same price as a decent recon rack might cost.

Longer version of BHM7113 about 7.5" long, new and fits all Mini Spares current steering racks from January 2011. Both gaiters are identical.

one kit required per steering rack with plastic clips

17H6298 si...

Non genuine gaiter kit with plastic clips for your steering rack is our best seller but see 17H6298 for single gaiter.

17H6298 single gaiter 4.5" long.

BHM7113 gaiter kit 4.5" long.

GR...

Non genuine replacement part track rod end for all factory mini steering racks. See also C-AJJ1572 for longer type with more thread or GSJ1106 for genuine type. Sold individually.

For all MK4 minis from 1976 until 1996 air bag models arrived.

Models from 1989 on only have one cancelling pin,match the boss to the existing wheel and remove unwanted pin.

Required to fit Mountney wheels to your Mini. The Mkl adapter Black boss has a built-in horn-push. The Mkll (BOSS/V3) is for cars with the horn on the stalk.