Rear Radius Arm and Bearings
Label Part No Description Quantity Comments
1 NAM7162 Radius arm bushed assembly R/H less No.5 1
1 NAM7162KIT Radius arm bushed assembly R/H with No.5 repair kit 1
1 TRA33 Reconditioned radius arm R/H with kit No.5 fitted 1 Old unit required
1 NAM7163 Radius arm bushed assembly L/H less No.5 1
1 NAM7163KIT Radius arm bushed assembly L/H with No.5 repair kit 1
1 TRA32 Reconditioned radius arm L/H with kit No.5 fitted 1 Old unit required
2 21A397 Brake pipe bracket 2 N.L.A
3 2A7351 Stub axle shaft R/H 1
3 2A7364 Stub axle shaft L/H 1
4 2A7352 Circlip for stub axle 2
5 GSV1125 Radius arm repair kit (single arm only) 2
6 ACA9099 Shaft for radius arm 2 All these parts are supplied in kit [link]GSV1125[/link] and note the outer bush requires reaming to correct size after fitment
7 2A7327 Rubber sealing ring 4 All these parts are supplied in kit [link]GSV1125[/link] and note the outer bush requires reaming to correct size after fitment
8 2A7324 Outer thrust washer 2 All these parts are supplied in kit [link]GSV1125[/link] and note the outer bush requires reaming to correct size after fitment
9 ACA9302 Inner thrust washer 2 All these parts are supplied in kit [link]GSV1125[/link] and note the outer bush requires reaming to correct size after fitment
10 2A7325 Bronze bush outer 2 All these parts are supplied in kit [link]GSV1125[/link] and note the outer bush requires reaming to correct size after fitment
11 GFK3215 Plain nut 1/2” UNF 4 All these parts are supplied in kit [link]GSV1125[/link] and note the outer bush requires reaming to correct size after fitment
12 LN10051 Grease nipple straight, was UHN400 2 All these parts are supplied in kit [link]GSV1125[/link] and note the outer bush requires reaming to correct size after fitment
13 RLH10021 Hub rear less wheel studs 2
14 21A1278 Wheel stud, 55mm stud shaft length with 20mm thread 8
14 ENJO-1039 Wheel stud, 58mm stud shaft length with 19mm thread 8 In [link]CW15[/link]/[link]CW16[/link] kit
14 ENJO-1040 Wheel stud, 78mm stud shaft length with 27mm thread 8 In [link]CW17[/link] kit
15 113087 Wheel nut, with 60 degree seat angle for steel wheels 16 Original equipment
15 CN5 Wheel Chrome nut, with 60 degree seat angle 16 Aftermarket fitting
15 AJM1139 Wheel nut, for alloy wheels less stainless steel cover 16 Original equipment
15 NAM9075 Wheel nut, for alloy wheels with stainless steel cover 16 Original equipment
16 GHK1548 Rear hub tapered bearing kit less ‘O’ ring [link]CDU1173[/link] (number 19) 2 Use GHK1805
16 GHK1548MS Rear hub tapered bearing kit non genuine 2
16 GHK1805 Rear hub tapered upgraded bearing kit with O ring [link]CDU1173[/link] 2
17 GHS102 Oil seal 2
18 GHF511 Split pin for stub axle shaft/nut 2
19 CDU1173 ‘O’ ring for stub axle inner. Fitted from 1996 only 2 Part of GHK1805
20 BTA672 Washer for rear hub nut 2
21 NL610041 Castle nut R/H with right hand thread 1
22 FNN2410 Castle nut L/H with left handed thread 1
23 ATB4098 Grease retaining cap 2
24 SR4 Spacer for rear wheel 1/8” (5mm) without studs 1pr Rover used 8mm so use [link]SR3[/link]&[link]SR4[/link] combined
24 SR3 Spacer for rear wheel 3/16” (3mm) without studs 1pr Rover used 8mm so use [link]SR3[/link]&[link]SR4[/link] combined
24 CW17 Spacer kit for rear wheel 3/4” (19mm) with studs 1 Special fitment only
Safety Critical Notice: When fitting wheel spacers ensure they are the correct specification for your vehicle not causing undue loading on any components.

Note: No16. GHK1805  had improved tapper bearing rollers for use on 13” wheels as a Rover warranty bulletin upgrade with an ‘O’ ring for the stud shaft to prevent water penetration. Radius arms were machined with a recess for the 'O' ring from 1996 on.