CLUTCH SLAVE CYLINDER PRE VERTO GENUINE
GSY110

($27.63) £27.63 exc vat

($33.16) £33.16 inc vat

In stockIn stock
genuine AP from the original tooling. The Mini Pre Verto clutch slave cylinder is a vital link in the proper operation of the Mini clutch. The master cylinder feeds the slave cylinder to exert the mechanical pressure to dis-engage the clutch. The simple sounding process is only complicated by a worn cylinder. As the wear continues it first will probably bypass, this will mean that the clutch will not stay dis-engaged when holding the pedal down. The next more obvious sign is when you see actual fluid leaking.

The slave cylinders are easy to replace.

The cylinder bore size is 7/8" diameter. Repair kit is GRK4008.

Bolt to hold slave cylinder is GFK5240.

($27.63) £27.63 exc vat

($33.16) £33.16 inc vat

In stockIn stock

Recommended usage 1 x GSY110 to fit one mini.
Diaphragm Clutch & Slave Cylinder - 1964 ON - Qty 1

Recommended products

The push rod on your clutch arm held in by clevis pin CLZ518 that goes into the slave cylinder. Check the eyepiece for wear.

The same push rod was fitted to both Verto and Pre verto slave cylinders.

This plate is on the end of the PRE A plus original long type clutch arm 22A2204 to hold the return spring 1G5999. The clevis pin to hold this on the arm is CLZ518.

If you have the later Mini Spares arm...

Clutch arm return spring for the return of the slave cylinder push rod. Total length 90mm.

Remote type gearboxes had four UNC bolts holding the long alloy housing to the differential case. These are the shorter two, 3/8"unc 1"long. The longer two are ZCS628.

Also the bolt to hold the starter motor.

Also the bolt for the [...

Anchor tab for return spring that fits behind bleed valve on Slave cylinders, for Pre Verto clutches.

Alternative products

Non Genuine slave cylinder. The Mini Pre Verto clutch slave cylinder is a vital link in the proper operation of the Mini clutch. The master cylinder feeds the slave cylinder to exert the mechanical pressure to dis-engage the clutch. The simple soundi...

People also bought products

Flat top clutch master cylinder to suit PRE 65 minis.

Originally the top of this master cylinder would have had either a removable union or a small hexagonal nut shape machined into it, but neither of these options are available so the pipe ...

Pre verto flywheel bolt and keyway washer in EN24T



The bolt is CNC machined from stock EN24T steel with extra attention to the radius under the head to maximise strength.

Clutch master cylinder for all ADO16 models-Austin 1100/1300 and derivatives-

not for mini as the push rod is longer on this.

Plate on the end of the PRE A plus long type clutch arm 22A2204MS to hold the return spring 1G5999. The clevis pin to hold this on the arm is CLZ518--this is the square type but for earlier tapered type Rover ar...

Pre verto race quality tuftrided clutch arm kit made in EN24T for any heavy duty diaphragm- special design plunger with arm to suit, hardened clevis pin and R-clip included.

Race quality bolt-sold seperately- these shorter bolts hold the spring straps 2A3658 to the flywheel on diaphragm type flywheels only. Not for Verto flywheel.

Only tighten up to 16lbs per sq foot torque when using shake proof wa...

Race quality shoulder bolts for the Mini clutch backplate to the diaphragm--sold seperately- heavy duty racing type EN16 tightenn up to 16lbs per sq foot torque when using shake proof washer or 18lbs and locktite. Use with C-2A3659 race ...

Braided one piece clutch hose from master cylinder to slave cylinder for left hand drive cars. Suitable for verto and pre verto clutch set ups, 91cm long.

Heavy duty clutch release bearing with a wider surface area, helps to spread even pressure on the clutch diaphragm and is favoured by racers.



small face with numbers stamp-face outwards, larger surface aera side face flywheel.

Anchor tab for return spring that fits behind bleed valve on Slave cylinders, for Pre Verto clutches.

Upgraded pre verto clutch lever arm plunger. Surely to be copied by competitors as the early diaphragm clutch really needed a quality item to be remade. This is the carrier that holds the clutch release bearing and on the other end has a hole for the...

Performance type Verto 180mm wide paddle type drive plate as used for racing.

Alternative to AP Racing plate

Mini Spares Performance clutch plate.

Great upgrade for increased performance engines,tested to 10,000rpm and to destruction for evaluation.

For diaphragm type clutch, pre verto. Great clutch plate and a better priced alternative t...

Borg and Beck Clutch Plate,upgraded when fitted to ERA Turbo,great plate for lightly tuned cars from 850-1275cc.

Upgrades after this are C-AHT595 which is ideal for any std road use on 1275cc and C-AHT596 from AP r...

Delete the metal pipe and existing hose by fitting this longer one piece steel braided pipe which can be used for either early or verto clutches. A sensible modification for all mini owners.

Easy bend copper 12" brake pipe with 2 male ends for single line master cylinders---for clutch or brake on early minis but the longer HF14 might be easier for the brake master which was nearer 13" long. These kits or pipes are at least 3...

Clutch diaphragm, blue for 1275/1100/998/850 Mini, pre Verto.

This part superseded the GCC102 850-1100 diaphragm.

The bolt that holds the flywheel to the crank on cars with a diaphragm type clutch. Locked in place by 22A1155 locktab on the 88G508 key washer.

There are 3 of these shorter 5/16"unf bolts holding the spring straps 2A3658 to the flywheel on diaphragm type flywheels only. Not for Verto flywheel.

Only tighten up to 16lbs per sq foot torque when using shake proof washer or ...