($35.25) £35.25 exc vat
($42.30) £42.30 inc vat
In stock
($35.25) £35.25 exc vat
($42.30) £42.30 inc vat
In stockRecommended usage 1 x MORRIS05 to fit one mini.
Replacement ball joint shims, comprising of 2x 003"(.076MM) shims, 2x 005"(.127MM) and 2 x 010"(.254MM).
Tie rod extra hard rubber bush, harder than standard.
You dont want these bushes too hard as it can cause the threaded on the end of the tie rod to break under extreme conditions.
In theory the outer ones should be harder for rigidi...
All models of the Mini use the same rear hub (this piece holds the rear wheel bearings). The Mini's rear wheel bearings are more than adequate, usually requiring only occasional repacking with grease. The weak link may be the cast iron hub; it is not...
Angled grease nipple for the upper arm on the front suspension of all Minis
importantly lubricates the upper arm spindle which so often gets neglected so check yours out and make sure this nipple is working properly. Also fits rear radius ar...
Complete rebuild kit for rear radius arm as sold by us since 2005.
Beware of cheap imports that are available in the market as they do not have correct heat treatment where required and have no longevity.
Kit Includes: shaft, beari...
Mini Spares own to original drawing specifications with heat treatment correctly applied where appropiate.Lack of proper maintenance (grease) will make the pivot shaft and/or bearings wear that much faster. In severe cases the shaft may rust to the b...
Mini Spares product from own original tooling since 1989.This small sheet metal panel mounts below the horizontal seam, covering the pivot pin of the R/H rear radius/trailing arm.
This shroud uses 14A7091 rubber plug not suppl...
Special shims for adjusting your swivel pins on the front hub. See workshop manual for correct settings - these are 005 thou but if you need 10 thou see 2A4241.
The front tie rod on the Mini controls the fore and aft location of the lower front suspension arm of the car. In addition it provides a great degree of stability under braking. If your rod is bent or the bushes are worn then you need help. The Tie r...
Floor pan front to rear for the left hand side, only to the floor shape before rod change cars - ideal for MK1/2 restoration.
The weathered and cracked rubber you see is not actually the hydro displacer bag, but rather this rubber boot to protect it. Sold singly 1 required per displacer.
For Hydrolastic suspension cars, they were made with a 1/4" fixing hole but this needs elongating vertically to get the bump stop to sit properly on the upper arm which had different machine tolerances when manufactured.
Have you got one of the rare "wet" suspension Minis? This is the retainer plate that holds the protective sleeve around the hydro hose on the bulk head panel.
Sold singly 2 required per car.
Longer track rod end for running with negative camber, gives an extra 5mm of adjustment approximately over the standard item. Has consistent thread pattern and perfect design to our requirements to fits all known racks and classed as a competition tr...
special double coil spring washer which fits on the rear hanbrake quadrant on Hydrolastic cars only.Known as a thackery washer
Front hub nut that screws onto the CV joint of all early minis with drum brakes plus all standard cooper 997/8 models. 1 1/8, 1.125" AF nut size although 28mm width have been seen. The washer for this is 2A7323.
Fits top and bottom of the front damper and the lower rear damper to keep the bush from moving in the damper (shock absorber) eye sockets. 3/8"hole.
1.4mm thick by 24.6mm wide.
Same bump stop as fitted to MGB, this was utilised by ST Works Abingdon to go on their bump stop kits C-AJJ3313/4007 for hydrolastic minis. Sold singly.
For the front wheel bearings of the Spridgets, rear of the Mini.
This is the flatter type rear rebound rubber on hydrolastic cars, uses exactly the same metal base plate as 21A1520 which is the larger cone type which is the bump stop rubber.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.