TRACKRITE TRACKING GAUGE
TOOL11

($83.31) £83.31 exc vat

($99.97) £99.97 inc vat

In stockIn stock
Simple and accurate tool for checking the wheel tracking-this tool is essential when suspension modifications or upgrades are carried out. A completely flat and level floor is not neccessary. Should also be used in conjunction with TOOL10 geometry tool.



Trakrite is the simplest, most accurate device for checking the alignment of the steered wheels of car and light commercials. It is a roller bearing platform over which one front wheel is slowly driven with the wheels in their straight ahead position.



Additional Information

• Tests accuracy in only 5 minutes.

• Easy and simple to operate with no technical knowledge needed.

• Easy to follow instructions.

($83.31) £83.31 exc vat

($99.97) £99.97 inc vat

In stockIn stock

Recommended usage 1 x TOOL11 to fit one mini.

People also bought products

We all knows Mini's like to leak a little oil... This drip tray is great for protecting your garage floor, low profile and measures 60x40cm.



Perfect for using whilst rebuilding heads, engines and gearboxes to keep all the small pa...

Metric & Imperial offset feeler gauge set, ideal for setting tappet clearnace, primary gear end float etc. Offset for ease of use.





Imperial: .005/.006/.007/.008/.009/.010/.011/.012/.013/.014/.015/.016/.017/.018/.019/.020/...

Imperial & Metric spanner set ideal for completing most tasks on your classic Mini, these are mirror polished spanners.



Contents: Bi Hex x Metric combination spanners 6, 7, 8, 9, 10, 11, 12, 13, 14, 17, 19mm and Stubby 10, 11, 12, ...

This tool bolts where the starter motor fits to lock the flywheel in place when trying to remove the flywheel bolt/crank pulley etc.

Red Rubber Grease has been specifically designed for use in environments where compatibility with seals and/or resistance to Hydrocarbons is required. Red Rubber Grease is compatible with both natural rubber and synthetic seals. The formulation of th...

Classic Castrol oil can with flexible spout and thumb pump.

Three arm oil filter wrench ideal for changing the spin on filters on Mini's. Comes with adaptor for 3/8" or 1/2" drive, suitable for filters from 65-120mm diameter.

Mini Spares offer this tool with a MSF166 filter for nearly no...

1/2" hex key socket needed when using our upgraded crank pulley bolt C-AHT147, 1/2" drive.

Copper Grease/Anti-Seize high melting point assembly grease supplied in 500g tub, suitable for jobs such as lubricating bolt threads, essential for any restoration project!

CV fitting tool, designed to assist with the correct fitting of CV joints, wheel bearings or drive flanges, as specified in the Haynes workshop manual. The wheel bearing should be torqued to the specified setting using this washer, and then removed a...

A series crankshaft tap in 5/8 x 16 tpi Whitworth form, used for both ends of the crankshaft.

Sykes Pickavent 21mm spark plug socket, 3/8" Drive

Roll pin punch for removing RPS1416 roll pin from the gear selector mechanism.

Molybdenum Grease supplied in a 500g tub, suitable for the lubrication of CV joints and any other homokinetic joints.

ESPECIALLY FOR MINIS

This 20-50w semi synthetic oil is produced especially for minis where it needs to lubricate both engine and gearbox parts giving the neccessary coating and protection. Semi synthetic has a long life to 100c with maximum ...

This new type suspension cone tool for removing or refitting the rubber suspension cone is METRIC thread only and improved by using a hex(allen)key to screw in and hold the centre spindle. There cannot be many cars left out there with the AF type th...

This tool/gadget allows you to balance both air intakes on either twin SU or twin choke carbs so they flow exactly the same to give better performance and economy.

Spanner for adjusting the jet on silver coloured original jets on HS type carbs

short handle to enable use in tight places such as a mini engine bay.

WILL NOT FIT LATEST BRASS TYPE ADJUSTER NUTS AS FITTED TO REPLACEMENT CARBS SINCE ...

A handy little gadget for fitting the circlip holding the rear wheel cylinder on

This sockket is for A plus flywheel nuts only-so if you have an early type diaphragm clutch use TOOL03