(45,36 €) £45.36 exc vat
(54,43 €) £54.43 inc vat
In stock
(45,36 €) £45.36 exc vat
(54,43 €) £54.43 inc vat
In stockRecommended usage 1 x 13H4461MG to fit one mini.
2.2 WATTS and fits back of gauges in cars with 3 extra 52mm round clocks.
This is the bulb holder for the original Smiths auxillary gauges fitted to 3 clock centre dashboards i.e 13H4459 and 13H4460, will also fit the aftermarket Smiths gauges (SIB part numbers).
Electric water gauge as standard on the centre binnacle Mini. Marked "C-N-H" Genuine Smiths. For post 1964 vehicles with voltage stabiliser fitted on speedo.
The early type had 3 connector tabs on one long brass strip for wires where as thi...
Magnolia face 0-110 centigrade scale with 6 foot capillary tube mechanical fittings, requires TE5 adaptor to fit cylinder head.
oil temperature gauge in magnolia.
If fitting MOCOT2 you will need TE5 adaptor.
Although the twin point minis had this type of gauge it worked electronically
which is not very accurate for performance engines. This one howe...
Smiths Electric oil pressure gauge in Magnolia.
Sender PTR1810-1-10 required.
This unit fits directly on to the gearbox in place of the standard cable and produces a digital signal for use with an electronic speedometer requiring a 5 volt square wave pulse such as our electronic speedo 13H4443. For pre 1980 speedo...
Brand new modern electronic version of the classic centre speedo, housed in a billet case with OLED display this unit fits as per original speedos. Features include:
*Trip and total miles
*Remote trip reset
*Driv...
This is the bulb holder for the original Smiths auxillary gauges fitted to 3 clock centre dashboards i.e 13H4459 and 13H4460, will also fit the aftermarket Smiths gauges (SIB part numbers).
Smaller 52mm face and reading 0-80 x100-If you are serious about your driving then you want to understand how your engine is responding to your urges. Many types of tachs are available in the aftermarket but since we drive British it should say "Smi...
With this large diameter line to the oil pressure guage you can actually see minor fluctuations in the pressure at idle or when the relief valve bounces open and closed. Because the braided steel line is one piece from the block to the gauge there is...
Angled oil pipe adaptor for fitting in confined spaces to eradicate damage of oil pipe, requires an OA adaptor if being used with a oil pressure gauge/t-piece.
Oil pipe in plastic 5 feet long, if fitting to a Tim gauge you will require LMA017 adaptor for the gauge.
Not comppatable with the CAM6431 standard oli pressure block union, and OA shoudl be purchased to fit.
Oil gauge adaptor for fitting into engine block or T piece.
A must if you want to run a mechanical oil gauge and retain the oil warning switch. Screws straight into the block on all A series engines.
If you have a 3 clock instrument panel from 1988 on (Nippon seiko stamped on them) it probably has black dials and these will convert your clock to the more fashionable magnolia white colour other colours are avaiable --add the colour to the part num...
Oil pressure is the "blood pressure" of your engine! Know how it is doing and you know how your engine is doing. This Smith's gauge is the standard 2" diameter with chrome bezel. With a magnolia face. Mechanical.
Does not come with pipewor...
Extra long cable for Smiths central located speedo when position moved in dash and also used as a Tacho cable for Sprite, 36" long.
2.2 WATTS and fits back of gauges in cars with 3 extra 52mm round clocks.
This is the oblong metal box attached to the rear of your round centre speed heads to stabilize voltage to the fuel gauge. For Centre clock Speedo only!
made for negative earth only--BR1310
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.