(8,93 €) £8.93 exc vat
(10,72 €) £10.72 inc vat
In stock
(8,93 €) £8.93 exc vat
(10,72 €) £10.72 inc vat
In stockRecommended usage 1 x 14A9786 to fit one mini.
The special pointed shape buffer locates against the boot board of Cooper S and variants where a factory type boot board is fitted.
The bracket fitted to the boot board and is not in any kits.
When a boot board is fitted the following brackets are required
14A9780x2 U shaped for the rear to hold the board
14A9781x2 side bracket with plug for board to si...
This kit contains all the floor brackets and mounts required for fitting Minis with 7.5 gallon tank 10/12" wheels or with 165 profile tyres.
The boot board bracket 14A9783 is not included
For 10" wheels with 145 tyres ...
This kit contains all the floor brackets and mounts required for fitting Minis with 7.5 gallon tank 10/12" wheels or with 165 profile tyres.
The boot board bracket 14A9783 is not included
For 10" wheels with 145 tyres ...
bracket for boot board R/H on 7.7 gallon tank and on both sides for 5.5 gallon tank when 165 tyres fitted
L/H BOOT BOARD BRACKET FOR 7.5 GALLON TANK AND 165 TYRES.
L/H BOOT BOARD SIDE BRACKET FOR 7.5 GALLON TANK.
This very heavy duty bonnet strap is a excellent reproduction of the original factory Special Tuning department special. A copy of our Tan leather strap, but now available in black.
3.3mm thick from the tanneries for use on horse bridles,wit...
Round spare wheel clamp with bolt for fitting in the boot to the spare wheel boss as fitted to Mk1 minis. See 88G479 for the boot floor boss that this clamp screws into.
Used on all MK1/2/3 bootlids there are 26 little holes drilled around the inner edge to hold the seal on and this kit contains the 26 clips. For single clips see 14A6585. Later cars 1988 on fitted a seal to the body only. (CKE10018)
This is the only hinge available for your pick up tailgate as the factory stopped making them before the millennium. Not genuine but a very good replacement when beggars cannot be choosers.
This kit contains all the brackets and mounts that were fitted on to the floor on original Coopers, Wolseley Hornet and Riley Elf with boot boards fitted as standard.
This kit does not include the bracket on the boot board 14A9783
These gaskets should be changed when replacing the hinges, this one goes between the bootlid hinge on the body, see 24A2175 also for upper on bootlid.
These gaskets should be changed when replacing the hinges-this one goes between the bootlid hinge on the bootlid. See also 24A2176 for gasket on body.
These chrome spring type clips are used to keep the bonnet and boot from coming open on competition cars and are available in black. Holes will be required in the fitting of these so if you do not want to drill your body panels these are not for you....
If you have twin original 5.5 gallon tanks this 26" wide boot board is the one for you.
Bootlid seal for Mini <91. Held in place on the boot lid using 26 clips(part# 14A6585).When fitting, the lip part of the seal open end for clips should face the inner boot catch- (the open end of the seal facing inwards to the bootlid al...
If you want your door and bootlid to have new or matching keys this is the easy way. The standard set includes two barrels with matching keys. This is only suitable when you require a drivers door and boot handle to match on MK1/2 cars only. This fit...
Do not forget to replace this little rubber seal that stops water getting into the boot lid via the handle hole. For sliding window type cars the door locks use ADA3817.
On mk3 models the small door gasket on the Mk3 wind up window door hand...
These two simple cables are all that keep the boot lid from crashing down, damaging hinges, bumper and paint. When one fails we recommend replacing both to be sure of the same length. sold singly 2 required per car
37H3043 can be u...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.