(69,54 €) £69.54 exc vat
(83,45 €) £83.45 inc vat
In stock
This allows you to delete the catalyst and fit an RC40 complete system.
(69,54 €) £69.54 exc vat
(83,45 €) £83.45 inc vat
In stockRecommended usage 1 x C-AEG367 to fit one mini.
Manifold gasket fitted to all A series pre 1992 except Turbo which had a reinforced exhaust ports GUG704063MG and SPI from 199. From 1991 on a new better gasket with reinforced exhaust ports and backing was fitted GUG704053MG
Twin Down pipe clamp for Carb Coopers 1990 on wards, and Metro's.
Also used as a single clamp on manifold for cars fitted with HIF38 carb cars from 1991 on.
This is the clamp on the cooper freeflow manifold to clamp it to the engine for extra support, supplied with tag.
Standard bore road LCB (1-3/4"id) that has an enlarged and reshaped middle pipe which creates a type of vortex, simulating a pulsing effect similar to the outside two pipes,thus producing an improved BHP,Torque and power curve.Ideal for very hot smal...
Standard bore Budget priced LCB (1-3/4"id) with pre cast flanges to improve flow and save engine tuners time matching the ports. This is ideal for very hot small bore engines and for standard to high performance 1275s, including road 1380s.
Small bore Maniflow LCB. Has a 1.5" outer diameter 1.375" internal diameter bore size. STD mini exhaust and downpipe size is 1.250".
If the 1.375" tapered end of about 2" is removed a 1.750 pipe will fit over remaining length of outlet pipe.
Special reinforced gasket for injection cars has metal inserts on exhaust ports plus a metal back on the manifold side which makes surface easier to clean when replacing. Often used on Turbo cars when correct gasket is in short supply.
...
Exhaust manifold to downpipe clamp.
The key to eliminating exhaust leaks at the manifold flange is the clamp. These new clamps include proper brass nuts and support washers. Fits most 850cc, 948cc, 998 etc. Those engines with single carb an...
For the medium bore Maniflow LCB Y piece or AN180V. 48mm ID
Maniflow's tubular reproduction of the original Cooper 997/998cc exhaust manifold manufactured out of the same tubing as the STD bore LCB. This free flow manifold works vey well at lower speed pick up, the LCB is noisier but better at the top end of ...
Special tin plate type of gasket that goes between the manifold and exhaust downpipes on all injection cars.
The intake/exhaust manifold should be secured to the head with brass nuts and these very thick washers. These washers are intended to not only spread the clamping action but the thickness allows them to absorb the heat without deforming! Takes 4 per ...
This short pipe fits on the end of our freeflow manifols C-STR816 to give the overall length of an LCB when you have an exhaust system to fit that was made explicitly for LCB fitment.Total length is 300mm ID is 44mm OD is 48mm.
Manifold gasket fitted to all A series pre 1992 except Turbo which had a reinforced exhaust ports GUG704063MG and SPI from 199. From 1991 on a new better gasket with reinforced exhaust ports and backing was fitted GUG704053MG
If you wish to delete the catalyst (legal restrictions apply, so check to see if you are allowed) this pipe is specially made to replace it.
Link pipe for fitting between the LCB and the catalyst. It has a stainless steel knuckle joint to prolong life and give the flexibility required on the system to overcome damage. See also alternative RC40-016
Y piece replacemen...
Manifold stud for all A series injection engines and some late carburettor cars which is 45mm long-6mm longer than 53K487.carburettor engines usually retained the 53K487 shorter screw for the outside 2 holes.
Sold singly,6 per c...
1.75" bore single box, centre exit exhaust system. This exhaust system by Maniflow is straighter and louder than our RC40 system. Very high quality with a skid plate on the bottom of the silencer and a polished stainless tip. Suitable for use with an...
This 5/8unf steel hexagonal head blanking plug was made for the inlet manifolds where the servo union can be fitted, plus blanking off the thermal transmitter hole under the thermostat. Uses 1B3664 washer ----------please note this will ...
Locating rings originally made for 12G295 heads with twin carbs to line up the inlet manifold to the inlet ports on the cylinder head it found its way on most twin carb factory produced cars. There is a recess in the inlet port on the he...
Genuine mini Spares inlet manifold dyno tested and designed for our Stage one kit C-STN17. The single SU manifolds is developed to give maximum airflow and gas speed, yet fit all engines even if the standard air cleaner set-up is used. I...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.