£243.08 exc vat
£291.70 inc vat
In stock
Using all the top quality tried and tested parts the Kit includes
RC40 twin box RC40 exhaust system and downpipe,
Maniflow's Cooper Freeflow exhaust manifold,C-STR816
Torquemaster inlet manifold, C-AHT770
K&N air filter element, E2601
carburettor needle, exhaust fitting kit, and gaskets for the carburettor and manifold.
PS- Assuming the carb and distributor are not worn the car should be rolling road tested for correct ignition timing and fueling for emmissions to optimise the best power available as present fuels available can compromise the choice of correct carb needle.
£243.08 exc vat
£291.70 inc vat
In stockRecommended usage 1 x C-STN17 to fit one mini.
STAGE 1 KIT. Mini Spares bolt-on performance kit for 998 and 1098 engines gives 20% more power and 12% more torque.
This money saver kit however is for further stages of tune and contains a Maniflow LCB exhaust manifold- twin box RC...
The stock air cleaner housing for many Minis with single 1 1/2" SU carbs have historically been stuck with the paper filter. New from K&N is a replacement element for FZX3013 and all HIF that provides the benefits of K&N cleanable filtra...
Complete mounting kit for the RC40 exhaust. Includes all new rubber mounts, brackets and clamps.
Gasket for an HS4-carb and manifold .Sold seperately and order as required for your car(usually 3).
Manifold gasket fitted to all A series pre 1992 except Turbo which had a reinforced exhaust ports GUG704063MG and SPI from 199. From 1991 on a new better gasket with reinforced exhaust ports and backing was fitted GUG704053MG
The favourite and best needle for Minispares stage one kit. Tested on a rolling road by Peter Baldwin this baby gave the best performance when using our RC40 system, Minispares inlet and exhaust manifold plus a K&N filter.
If us...
This plug fits our inlet manifolds and Rover types with servo take off holes..
5/8 UNF grub screw that use 8mm allen key for blanking inlet servo take off or temp transmitter hole at front of pre 1996 cylinder heads. Can also use ADP210
Maniflow's tubular reproduction of the original Cooper 997/998cc exhaust manifold manufactured out of the same tubing as the STD bore LCB. This free flow manifold works vey well at lower speed pick up, the LCB is noisier but better at the top end of ...
Mini Spares genuine RC40 system has justifiably earned the reputation of the best exhaust ever made for the Mini. Mild steel with stainless steel tailpipe. Typically used with an LCB manifold it gives great performance with a mellow soun...
STAGE 1 KIT FOR MINI VAN, ESTATE AND PICKUP. Mini Spares bolt-on performance kit for 998 and 1098 engines. Gives 20% more power and 12% more torque.
Always get your car rolling road tested for best ignition/timing and emmissions after fitmen...
if your front downpipe or exhaust needes replacing this conversion will give you extra power for little more. A new better flowing downpipe with a flexible knuckle plus our super RC40 single box rear silencer for that slightly sporty sou...
STAGE 1 KIT. Mini Spares bolt-on performance kit for 998 and 1098 engines.
Similar to C-STN17 except it has a large bore side exit exhaust.
Always get your car rolling roaad tested for best ignition/timing and emmissio...
Exhaust manifold to downpipe clamp. For 32mm o/d pipe size.
The key to eliminating exhaust leaks at the manifold flange is the clamp. These cast clamps are the best style to use. A real piece of kit to use eradicating a multitude of likely p...
Rear RC-40 twin box system to fit catalyst for cars built late 1991 on SPI(not early carb coopers). It has the hanger rods fited for mounting onto the rubber type straps. This makes it a twin box system with a little throatier pleasing note, but a mu...
1.75" bore single box, centre exit exhaust system. This exhaust system by Maniflow is straighter and louder than our RC40 system. Very high quality with a skid plate on the bottom of the silencer and a polished stainless tip. Suitable for use with an...
Stainless steel tailpipe trim with hanger bracket designed for fitting to the tailpipe of RC40 rear box as an extension piece. This is part of our RC40PACKAGE015 kit for Van/Estate and Pickup exhaust system when a freeflow o...
This sleeve will allow an 1"3/4 rear box to fit a standard bore front pipe of a 998cc mini. The large end fits into the RC40 and the smaller end accepts the 1.25" diameter as standard 850/998 exhaust pipe bore
This is the clamp on the cooper freeflow manifold to clamp it to the engine for extra support, supplied with tag.
Stainless steel version of C-AEG376. Standard bore road LCB (1-3/4"id) that has an enlarged and reshaped middle pipe which creates a type of vortex,simulating a pulsing effect similar to the outside two pipes,thus producing an improved B...
Standard bore road LCB (1-3/4"id) that has an enlarged and reshaped middle pipe which creates a type of vortex, simulating a pulsing effect similar to the outside two pipes,thus producing an improved BHP,Torque and power curve.Ideal for very hot smal...
Original exhaust bracket for rod change gearbox but later on Rover reverted back to GEX7526 which seemed a bit of a backward cost cutting exercise.
The famous RC40 mild steel centre exit large bore outlet exhaust with a new state of the arts exhaust manifold plus the fitting kit for the exhaust system.
There is NOT enough clearance room when fitting to old cars with rubber ...
Exhaust centre strap that hangs from the mounting on the centre of the rear subframe, for saloon models only as the van is longer(GEX7273).
The clip on the exhaust that this attaches to is GEX7052 and is usually on a new exhaust...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.