£84.23 exc vat
£101.08 inc vat
Out of stock
£84.23 exc vat
£101.08 inc vat
Out of stock
Complete mounting kit for the RC40 exhaust. Includes all new rubber mounts, brackets and clamps.
Stainless steel tailpipe trim with hanger bracket designed for fitting to the tailpipe of RC40 rear box as an extension piece. This is part of our RC40PACKAGE015 kit for Van/Estate and Pickup exhaust system when a freeflow o...
This short pipe fits on the end of our freeflow manifols C-STR816 to give the overall length of an LCB when you have an exhaust system to fit that was made explicitly for LCB fitment.Total length is 300mm ID is 44mm OD is 48mm.
Exhaust manifold to downpipe clamp. For 32mm o/d pipe size.
The key to eliminating exhaust leaks at the manifold flange is the clamp. These cast clamps are the best style to use. A real piece of kit to use eradicating a multitude of likely p...
The very rear bobbin type mounting rubber on every mini made until the introduction of a rubber hanger strap in 1992. When the RC40 or similar systems are fitted, 2 will be required. This is a stronger poly version.
Standard bore road LCB (1-3/4"id) that has an enlarged and reshaped middle pipe which creates a type of vortex, simulating a pulsing effect similar to the outside two pipes,thus producing an improved BHP,Torque and power curve.Ideal for very hot smal...
Standard bore Budget priced LCB (1-3/4"id) with pre cast flanges to improve flow and save engine tuners time matching the ports. This is ideal for very hot small bore engines and for standard to high performance 1275s, including road 1380s.
Middle exhaust mounting, bolts on to the front of the rear subframe and is the central or first of the rubber mountings. see GEX7081POLY for Poly type or if you are fed up with breakages see C-19G3257.The original Genuine pa...
Small bore Maniflow LCB. Has a 1.5" outer diameter 1.375" internal diameter bore size. STD mini exhaust and downpipe size is 1.250".
If the 1.375" tapered end of about 2" is removed a 1.750 pipe will fit over remaining length of outlet pipe.
Special reinforced gasket for injection cars has metal inserts on exhaust ports plus a metal back on the manifold side which makes surface easier to clean when replacing. Often used on Turbo cars when correct gasket is in short supply.
...
This 5/8unf steel hexagonal head blanking plug was made for the inlet manifolds where the servo union can be fitted, plus blanking off the thermal transmitter hole under the thermostat. Uses 1B3664 washer ----------please note this will ...
Standard bore LCB (1-3/4"id) that is ideal for very hot small bore engines, for standard to high performance 1275s and for street 1380s.
There is NOT enough clearance room when fitting to old cars with rubber couplings which foul. Using [lin...
The center exhaust hanger takes a lot of abuse during hard acceleration or if you're low enough to bottom out on bumps. This mount has a through metal bolt to keep it intact.
This magic pipe will allow you to upgrade to the larger bore twin box RC40 without having to change from your existing standard exhaust manifold on 998/1100cc engines. Ends where a LCB would normally finish so order the RC40-002...
STAGE 1 KIT. Mini Spares bolt-on performance kit for 998 and 1098 engines with HS4 carb. Gives 20% more power and 12% more torque.
Using all the top quality tried and tested parts the Kit includes
RC40 twin box [link]RC...
Maniflow's tubular reproduction of the original Cooper 997/998cc exhaust manifold manufactured out of the same tubing as the STD bore LCB. This free flow manifold works vey well at lower speed pick up, the LCB is noisier but better at the top end of ...
Special tin plate type of gasket that goes between the manifold and exhaust downpipes on all injection cars.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.