£0.56 exc vat
£0.67 inc vat
In stock
£0.56 exc vat
£0.67 inc vat
In stockRecommended usage 3 x AEC2083 to fit one mini.
Alloy spacer (0.535" 13.5mm) for 1.5 SU carb against inlet manifold, does require paper gaskets AEC2083.
New Carb Spacer for HS4 carbs with vacuum take off. 7.5mm thick.
STAGE 1 KIT. Mini Spares bolt-on performance kit for 998 and 1098 engines.
Similar to C-STN17 except it has a large bore side exit exhaust.
Always get your car rolling roaad tested for best ignition/timing and emmissio...
Kit includes genuine head gasket, valve cover gasket, manifold gasket, thermostat gasket, all carb gaskets, etc. Fits all 850/998 948cc and 1098cc Pre A plus engines. Use Minispares parts together with a GUG702506HG head gasket
Not Built up= A Complete kit of HS4 CARBS/ MANIFOLD/LINKAGE LESS AIR CLEANER
STAGE 1 KIT. Mini Spares bolt-on performance kit for 998 and 1098 engines with HS4 carb. Gives 20% more power and 12% more torque.
Using all the top quality tried and tested parts the Kit includes
RC40 twin box [link]RC...
STAGE 1 KIT. Mini Spares bolt-on performance kit for 998 and 1098 engines gives 20% more power and 12% more torque.
This money saver kit however is for further stages of tune and contains a Maniflow LCB exhaust manifold- twin box RC...
Performance Stage one kit for 1300cc models with HS4 or HIF38 Carb with side exit large bore exhaust system RC40-010
Always get your car rolling roaad tested for best ignition/timing and emmissions after fitment.
STAGE 1 KIT FOR MINI VAN, ESTATE AND PICKUP. Mini Spares bolt-on performance kit for 998 and 1098 engines. Gives 20% more power and 12% more torque.
Always get your car rolling road tested for best ignition/timing and emmissions after fitmen...
STAGE 1 KIT. Mini Spares bolt-on performance kit for 998 and 1098 engines.
Similar to C-STN17 except it has a centre exit exhaust.
Kit includes - single box RC40 Millennium large bore centre exit exhaust system,...
SU conversion Jet for conerting from a waxstat jet to conventional without having to buy a different linkage etc.
This is the original type of needle valve that governs the plastic fuel float in your SU carb.
An alternative better upgraded version is available as CA90.
Twin carb HS2 (1.25")black heatshields with link bar and 3 new return springs.
Before the days of Aeroquip, Minis were fitted with braided steel rubber fuel lines. They should be used in place of rubber for all fuel lines in the engine compartment. They come made to length, with rubber end caps. 1/4" bore size.
Orange ...
Clip on the heater valve for heater cables on vehicles from 1990 where the in line remote heater valve was used. It has also been used as a clip for HIF carbs to hold the cable but the one from Rover is 13H3472.
Before the days of Aeroquip, Minis were fitted with braided steel rubber fuel lines. They should be used in place of rubber for all fuel lines in the engine compartment. They come made to length, with rubber end caps. 1/4" bore size.
Orang...
Stainless steel twin HS4 heatshields kit. Comes with Link bar and springs.
Throttle return springs for all twin carb variants. Usually 3 fitted.
This is the right hand linkage lever taht sits on the rods between HS type twin carbs. Sold individually
Air ducting tube from inlet manifold to air cleaner. These are 5.5" long which covers the longest but some such as the injection model is only 1.5" OR 2-2.5" long.
Manifold to carb gasket for HS2 single and twin carbs, usually 3 per carb required.
Used in petrol fuel lines to take 1/4" petrol hoses it is used mainly on twin carb set ups for petrol being diverted to the 2 carbs.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.