FLOAT NEEDLE VALVE MINISPARES OWN SUPERFLOW TYPE
CA90

£8.25 exc vat

£9.90 inc vat

In stockIn stock
If fuel is overflowing the float bowl the needle valve is leaking. This may be caused by the float WZX13040(GSU200) being misadjusted, stuck or leaking OR the needle may be fouled with a bit of grit or worn and not sealing. This is an

alternative updated version with brass/bronze rod which flows and wears better.

Fits HS2,HS4 and HS6 carbs but not HIF range. CA90 is ethanol tolerant

If living where Ethanol is dominant in your petrol(10%)and causing problems there is an alternative WZX1100A with a viton tip.

£8.25 exc vat

£9.90 inc vat

In stockIn stock

Recommended usage 1 x CA90 to fit one mini.
Carburettors HS2 - Qty 1
Carburettors HS2 Twin - Qty 2
Twin HS4 Carburettor - Qty 2
Carburettor HS4 - Qty 1
Carburettors HS4 - Qty 1

Recommended products
CARB GASKET SU FLOAT CHAMBER
AUC8459

Paper gasket for the float bowl of any HS2/HS4/HS6 carbs.

£0.80 exc vat

£0.96 inc vat
SU FLOAT AND GASKET
WZX1300

Plastic float and gasket-If fuel is overflowing the float bowl the needle valve is leaking. This may be caused by the earlier floats GSU200 being misadjusted, stuck or leaking, or the needle valve CA90) may be fouled with a ...

£8.70 exc vat

£10.44 inc vat
Alternative products
FLOAT NEEDLE VALVE HS2/4/6 (VITON TIPPED)
WZX1100A

This is the original type of needle valve that governs the plastic fuel float in your SU carb.

An alternative better upgraded version is available as CA90.

£10.38 exc vat

£12.46 inc vat
People also bought products
GENUINE SU HS STAYUP FLOAT KIT
WZX1304

The new adjustable height StayUp® Float is resistant to modern ethanol based Fuels and has a military spec closed cell construction making it puncture proof. The ability to adjust the Float Arm allows for quick and easy minor alterations to Float lev...

£19.60 exc vat

£23.52 inc vat
FLOAT NEEDLE/SEAT FOR HIF38/44 LARGER TYPE VALVE
WZX1099A

Fitted to HIF38 and HIF44 carbs, ethanol tolerant product. Bigger bodied valve.

For turbo models see WZX1095 .Quantity required-1

£20.43 exc vat

£24.52 inc vat
SPINDLE KIT HS4 1.5"
WZX1177

throttle spindle kit for single HS4 type carbs-.Quantity required-1 kit. -the butterfly is available seperately as WZX1323 for plain-WXZ1325 with air valve

£13.50 exc vat

£16.20 inc vat
CARB SPINDLE KIT 1.1/4" HS2
WZX1310

spindle and fixings only for the HS2 carb-the butterfly for this is WZX1320.

sorry folks but buying both kits you get double the gaskets

£11.70 exc vat

£14.04 inc vat
HIF44 JET ASSEMBLY
WZX1453A

jet assembly (0.100") for the HIF44 carb only- see MGM10008 for HIF38(0.090")

£25.76 exc vat

£30.91 inc vat
FLOAT NEEDLE VALVE HS2/4/6 (VITON TIPPED)
WZX1100A

This is the original type of needle valve that governs the plastic fuel float in your SU carb.

An alternative better upgraded version is available as CA90.

£10.38 exc vat

£12.46 inc vat
FLOAT SPINDLE HIF
CUD2082

spindle to hold the float to the float lid on the bottom of HIF carbs only.

the float is WZX1509A and needle valve is WZX1099A except turbo which is WZX1095

£4.93 exc vat

£5.92 inc vat
CARB JET TO FLOAT BOWL SEAL
AUD2194

The metal washer AUD2193 goes up against this seal on the jet where it enters the float bowl on all HS type carbs.

£1.01 exc vat

£1.21 inc vat
CARB SPRING (RED 4.5oz) HS TYPE CARBS
AUC4387

Standard spring for all HS2 and HS4 on minis except for the 997/998 Cooper from 1964-9 and H4 special tuning carbs which used AUC4587.

£7.59 exc vat

£9.11 inc vat
CHOKE CABLE TRUNNION ACH9042 NIPPLE & 53K3503 SCRE...
AUE34

Complete with screw the choke trunnion is used on nearly all SU carb linkages.

See ACC5062 for carb cable link trunnion also.

£2.03 exc vat

£2.44 inc vat
ORIGINAL BRASS TYPE CARB DASHPOT DAMPER
AUC8103HB

Early single HS" carbs had these splendid looking brass top dashpot dampers which are interchangeable with the plastic type.

£29.03 exc vat

£34.84 inc vat
BUTTERFLY SCREW
AUC1358

These screws fit all HS type carb butterflies to hold them on the throttle spindle

£0.90 exc vat

£1.08 inc vat
CARB HS2 SPINDLE REPAIR BUSH
AUD3079

Worn throttle spindles cause erratic performance from your carb and sometimes the housing gets worn--These are the bushes to repair worn carbs when replacing spindles for HS2 carbs. As a guidline 0.250" internal diameter and ream carb bo...

£4.16 exc vat

£4.99 inc vat
CARB FLOAT GROMMET 30° L/H FOR HS2/4 (orange)
AUC1316

Float grommet for the mini twin HS2/4 carbs---this 30 degree angle is for the L/H ( front) carb and is positioned to angle the float bowl--Used on both twin HS2/4 carbswhen using correct mini inlet manifolds- Midgets and MGB used different angles,u...

£10.19 exc vat

£12.23 inc vat
CARBURETTOR LEVER PIN
ACC5062

Pin to hold the accelerator cable which locates in the carb bracket lever. Supplied as originally fitted with washers, nut and split pin plus a proper machined hole for the cable unlike many others on the market- which come either bare or with wrong ...

£2.93 exc vat

£3.52 inc vat
FLOAT LID SEAL FOR HIF CARB
AUD3588A

Seal for the HIF38/44 float lid chamber

£1.95 exc vat

£2.34 inc vat
FLOAT PIN
AUC1152

The pin that holds the float bowl in place on the float bowl lid-See also AUE266 for complete lid with float bowl and needle valve fitted.

£0.68 exc vat

£0.82 inc vat
CARB DASHPOT DAMPER
AUC8103A

Fits single and twin HS2 carb dashpots but only single HS4 carbs(the twin HS$ use AUC8114) --See AUC8103HB for the original brass type fitted to early single HS2"

£23.52 exc vat

£28.22 inc vat
CARB FLOAT GROMMET 30° R/H FOR HS2/4 (purple)
AUC1336

Float grommet for the mini twin HS2/4 carbs---this 30 degree angle is for the R/H ( rear) carb and is positioned to angle the float bowl--Used on both twin HS2/4 carbswhen using correct mini inlet manifolds-Midgets and MGB used different angles,usual...

£10.19 exc vat

£12.23 inc vat
CARB HS4 SPINDLE REPAIR BUSH
AUD3080

Worn throttle spindles cause erratic performance from your carb and sometimes the housing gets worn--These are the bushes to repair worn carbs when replacing spindles for HS4 carbs. As a guideline 0.3125" internal diameter ream body to 9...

£3.71 exc vat

£4.45 inc vat